Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hi everyone,
Currently I'm using Android Nrf Mesh Library 2.4.1 for provisioning device into network.
I face the issue which can not be found why to fix this error.
...
I cannot set CONFIG_POWER_OPTIMIZATION_ENABLE to yes in the master branch. It leads to deadlock in at_cmd_write() because that ends up getting executed in the socket_thread...
I copied the slm application into a directory outside the SDK (e.g. C:\temp\slmapp) and I launched a command prompt from the nRF Connect's tool chain manager. Then I navigated...
Hi, I was trying to interface nRF 52840 with a SPI based NOR flash (IS25LP064A). I am using SPI example in 16.0.0 sdk version. But i am not able to read the device id as this...
Hi,
I use SDK15.3
There's no such define in "ble_gap.h"
Is this define "BLE_GAP_ADV_TYPE_EXTENDED_CONNECTABLE_NONSCANNABLE_UNDIRECTED" only S140?
Because 52811 use...
Segger Embedded Studio always starts with license error even though a nRF52840 DK is connected.
It always complains as follows:
"
Embedded Studio could not find a commercial...
I'm getting an undefined reference to "app_uart_init". I've enabled the respective libraries in the sdk_config.h:
//====================================================...
I tried to combine the Wireless_uart example with the USB CDC example to be capable of using both but it doesn't seem to be working.
When I plug my board using the nrf USB...
Hi there,
I am using WIN10, Segger studio 4.52c and nRF SDK16.
I can successfully run ble_app_uart example on PCA10056, but when i try to run same code on fanstel EV-840...
Hi, I have been working on setting up the environment for development of nrf52840 and nrf9160 the past three days. I have nRF9160 dk which comes with nrf52840. I have been...
When I built and run your example Bluetooth: Peripheral HIDS keyboard and I saw the following errors in logs: E: set-value failure. key: bt/ccc/283926aaa86c0 error(-2) E:...
Hi,
We would like to know whether below gang programmer can be used for gang firmware flashing of NRF9160 application FW and NRF9160 modem FW.
Also we would like to know...
I am getting the following error when trying to register a nRF9160-DK with a HWID. There was an error adding your device: nRFCode 40001:
Please advise how to move forward...
Hello!
I've got a couple of NRF52832 based modules - Holyiot-17095-nRF52832. These modules are presented in the list of supported - https://www.nordicsemi.com/Software-and...
