Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi,
I am using ppk2 to measure current on a custom board based on particle bsom (nrf52840). I am running ampere meter mode and I can measure some current, but values looks...
Hello Nordic Community,
I installed the serial LTE modem application on my Thingy:91 so that I may use it as a standalone modem. Using minicom on my Linux machine, whenever...
Hi,
I’m quite new to the nRF5 SoC’s and currently facing a problem with USB virtual com port communication using nRF52840 dongle (PCA10059) . I need to get results from...
Our project was previously functional when we were developing using the nrf52840dk_nrf52840 with an overlay to reconfigure for our custom pcba. We created a custom board config...
Hi,
I want to get the VBUS input detection status (USB detected or removed).
I have confirmed that the current state can be known by reading the value of the register...
I needed to rework the memory map, to change the size of the slots to accommodate for a larger foot print. In the programmer, is an "Erase & write" with the hex file sufficient...
Currently the CAF Bluetooth LE advertising module only uses static advertisement data in ble_adv_def.h
Would it be possible to add an interface for setting manufacturer...
Hi support,
We have a product that successfully utilizes DFU and is currently in production. However, we have been seeing a couple units that failed DFU but can still...
Hello all,
I'm trying to send SPI signal from nRF52-DK to other circuit component.
nRF52 doesn't receive data, and send 16 bit data at one transfer.
I want to send data...
Developing on nrf9160 using NCS 2.1.2 and MFW 1.3.3, is there any sort of Hard Fault detection and handler besides the k_sys_fatal_error_handler hook in lib/fatal_error/fatal_error...
Hello,
I recently ordered a Thingy:53.
The first time I turned it on, I successfully tried the Edge Impulse app, and updated the Thingy:53 network and app firmware via...
Hi, my slave will send 55 bytes to SPIM, if I check slave data when SPIM received all data, and it will spend 1.8ms, I think its long.
Can I check data when SPIM starts...
Dear Nordic team, We are using the nRF connect SDK version 2.1.2. Our prototype uses the nrf52840dk board and the KScan application template. However, when directly trying...
Hi,
Want to update the linker script as below in segger embedded studio? How to add this using flash_placement.xml. //update your linker script (.ld file) to expose information...
I'm trying to use the ADC on the DK52 (PCA100040) to sample and transmit data to a PC. I've been able to write code that samples data to a buffer and I've modified the peripehral...
