Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Hello,
I am trying to figure out a problem with the WDT module behavior
Running on an nrf52832 and using SDK 11 with softdevice s132 v2.0.0!
There are 3 WDT channels...
Hi,
I have nRF52840 DK with Power Profiler PPKI. It was working for long time, but now it suddenly stops working.
Screen saved:
nRFConnect Dektop version 3.7.1, Power...
After I changed from SDK 17.0.2 to SDK 17.1.0 I get for the example project "blinky_FreeRTOS_pca10040" during the compilation with IAR Embedded Workbench IDE - Arm 8.50.9...
Hi, I had designed custom board using icm20948. i tried to get raw values from sensor and succeed then i had ported nucleo code for nrf53 zephyr. when i tried to run below...
Hello,
I'm evaluating nrf52840 and trying to use zigbee/light_bulb as a starting point. One thing I caught immediately and still trying to find an explanation for was the...
Hi DevZone,
I need help to understand the DFU procedure over the Mesh without any second BLE dongle/BLE serial device to populate the DFU packets.
The ask is how can we...
Hi
I am using the nRF52840 with an external sensor which I need to config (nRF is the master). after this, nRF is acting like a I2C slave (twis) and i like to trigger an...
Hi,
I'm making my own program to upgrade the nRF9160's modem firmware over SWD. So far, application note nAN41 has helped a lot, but I'm getting stuck when trying to get...
Hello.
I need to transfer files from a phone to a BLE peripheral device. I have a small FatFS filesystem on an external flash chip on the device, and I'm now trying to decide...
Hi,
I have just setup the nRF Connect SDK for the first time. I am running Ubuntu 20.04 in a Virtual Machine. I followed the instructions in the "Getting Started Assistant...
Hi!
I'm trying to prepare FOTA firmware using instructions provided by: FOTA upgrades but it seems not working.I have couple of issues and questions. Please help me.
My...
Hello,
I have been experimenting with the new VSCode extension for the last week or so and I've noticed some issues. I understand that this is a currently a beta release...
Hello,
Is it possible to receive a review for a board i'm developing??
This board is to be used as a Raspberry Pi Hat to be able to communicate using UART between RPi...
How to recover communication due sequence number. (Could be due of PYACI serial hardware changed/dammaged). Is there any command to reset or know sequence number of node....
Hello all,
I'm developing a BLE CGMS application based on the experimental example on the SDK folder.
Now I working in the timing characteristics and I could see that...
