Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hello,
As part of a Proof of concept reason on nRF52840 based SDK15.2 and s132_nrf52_6.1.0_softdevice, our BLE communication should support Just Work security and no secure...
Hi there,
we are working on a number of nRF52840-based hardware products with almost identical functionality. Some have USB and BLE connectivity, while others offer BLE...
Hello,
I am working in NCS and I am trying to save some data in flash before the SoC turns off.
I am starting by using the code below.
If I use this code in the main...
Hello everybody. Using the nRF52840-DK board and the Nordic example ble_app_uart_pca10056_s140 I am sending 200 bytes, repeatedly, to the Nordic UART APP. Everything works...
Hi,
What is the best approach to use a block of flash in nrf52840 as EEPROM. Are there any pre-existing library support for the same?
Also which is the best flash operation...
Hi,
I have gone through the lfs file system from zephyr samples but I could not find any solid documentation for fs and spi flash drivers available.
I have written the...
Hello,
I want to use the PWM driver to change the output voltage with respect to analog input voltage. If I call the simple_playback_sequence from the SAADC event handler...
Good day. Some smartphones cannot connect to NRF52832 (SDK17): - iPhone XR - iPhone 11 Detection goes well, but smartphones cannot fully connect and freeze at the connection...
Hi Sir,
We tried to download the nwp_024 , and check the tape reel information of nRF5340.
But we could not find the nRF5340 lists in "table 2. Carrier tape dimensions...
Hey everyone,
I firstly want to preface this with my lack of credentials. I'm very new to embedded systems development and am figuring things out slowly so please bear with...
I want to initialize LFCLK on startup to reduce power consumption. I am doing it as given below. Is this the correct approach of initializing LFCLK to reduce power consumption...
Hi,
I am using nRF52840 as BLE peripheral, on a Zephyr application under NCS 1.4.2
I want to limit the connection interval to 7.5ms (min+max)
I can see that the only...
Hi Nordic DevTeam,
I am using nRF52840 (1MB Flash, 256kB RAM). I would like to store a log data to flash memory that I can extract them to my Android phone later on when...
