Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
I'm unsure if this is the correct place to post since this is not a Nordic-specific issue.
I am using the P100 which is a nrf52840 connected to an HL7800 through a UART...
hi all
i want to use a chip antenna for nrf52840
but un data sheet there is not any sample layout or component details
for example i want to use this chip antenna
...
Subject: Query: Interfacing OLED SSD1306 with nRF52832 on Zephyr
Dear Zephyr Dev Zone Community,
I hope this message finds you well. I am currently working on a project...
Hello! The S140 7.3.0 SoftDevice docs say it requires 0x27000 of flash, but the SoftDevice hex only occupies 0x26634 bytes. This leaves 2508 bytes of hopefully unused flash...
Hello, I'm trying to confirm whether the front-end module (FEM) is actually active in my application. Here is a summary of what I have done so far:
Updated prj.conf...
I followed the example described in https://developer.nordicsemi.com/nRF_Connect_SDK/doc/2.2.0/nrf/ug_nrf52_developing.html#fota-updates
and the loaded the SMP Server example...
Hallo,
currently I test several options in regarding the use of advertising. I have a few nRF52840-DK and use Zephyr 2.7-99 and ncs. I have a question regarding combined...
We are using SDK v2.6.1 for our application, along with the Fanstel module WT02C40C.
In our application, we provide internet connectivity to the WT02C40C module via a mobile...
Hi,
I have a makefile generating an elf and then a hex and bin file for a nrf52 project. Now I builded up a zip file for bootloading. Which works as well.
Now in our CI...
We are running an HCI controller on nRF52833 based on the Zephyr hci_uart sample code. We are using the Zephyr 3.7.0 LTS version.
We have set CONFIG_BT_CTLR_DATA_LENGTH_MAX...
I want change toolchains, so when i open nrfconnect terminal I can use my own west command. I've read link , link and link
Option in the picture lets me install or open...
Hi,
There were GPIO /SPI Interface headers are given on NRF21540 EK .now how we can connect RF input to TRX pin of NRF21540.
please provide the Understanding of RF input...
Hi
We are looking into connecting an external GNSS antenna to the Thingy91x board. The drawings metion 2 ports J1 and J2 but can't find anything in the docs if these are...
