Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
Hi there,
i'm wondering if it's possible to get access from the demodulator directly within the nRF52? it shows in the block diagram below, is there any way to bypass...
Hello Nordic,
I'm trying to run nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_uart (PCA10056, S140 softdevice) with default sdk_config.h . The master is nRF Connect...
Hi,
I am new to nRF Connect SDK. I am trying to achieve over the air Firmware upgrade through nRF5340. The SDK i am using is nRF Connect SDK v1.5.0 .
As per my understanding...
I am currently going through the usbd_ble_uart example and understanding what states make which LED's active,
Within the example, LED_BLE_NUS_CONN is defined as BSP_BOARD_LED_0...
How to use the internal 32.768k crystal oscillator for nrf5340？
NCS: V1.5.0
example: ncs1.5.0\v1.5.0\nrf\samples\peripheral\radio_test
Only HF no LF config.
Hi all,
I'm trying to use one of the built in sha256 libraries. As I've enabled the CONFIG_NRF_CC3XX_PLATFORM and CONFIG_NORDIC_SECURITY_BACKEND I thought I would pick this...
I am working on a BLE Product which connects to a remote device when detected within a certain proximity (based on the RSSI values). After switching on the scanning, I receive...
Hii Guys,
I am trying to run example code ble_app_uart on my nrf52810 sdk module . But when I try to run the code in debug mode I get an error of Vector Catch Error ....
Hi, I am working on nRF52840. I want to add GSM MQTT protocol. Is there nordic soc available for this? Which we can later communicate with nRF52840 peripheral device also...
Hi Everyone,
I am working on nrf52832, I am using sdk15.0.0 ble_beacon_app.
I want set tx_power but when softdevice enable gettting error.
I am tried using sd_ble_gap_tx_power_set...
Hi.
When I click add new LTE Device, I get the same menu as when clicking add new SIM Card. When is click register with IMEI and PIN assosiated to my nrf9160DK, I get. ...
Hello All,
I am developing a light control device using Zigbee and Alexa. I am using an nRF52840 device and SDK nRF5_SDK_for_Thread_and_Zigbee_v3.0.0_d310e71.
For my development...
Hello Everyone,
I am a beginner
I am working on a project which requires authentication of the firmware , for this purpose i want to generate the hash of the firmware...
Hello OT Team,
I am working on the custom product where Openthread would be used. I am facing the issue while commissioning the other device to join the network.
The...
Hi ,
I tried following steps to configure and toggle GPIO pins.
I have also set CONFIG_GPIO=y i n your prj.conf file. ,referring to https://devzone.nordicsemi.com/f...
