Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
If a heartbeat or other chunk reliant on symbol file data is ingested when there is no symbol file associated with the Software Version / buildID it seems like the chunk is...
Hello,
I am currently trying to make an application that can do FOTA and store the secondary firmware image on an external flash using sQSPI. The project I started is based...
Hello,
We use the nrfx spis driver for communication between a ST processor (master) and a Fanstel BT840 module (nRF52840).
We have upgraded ncs from 2.6.0 to 3.2.1 and...
I am using a GPIO pin ( P1.05 ) as a reset signal for an external CPU component. The pin functions correctly and stays low when tested in a basic GPIO application. However...
I'm using NCS 3.2.4. When USE_PARTITION_MANAGER is active, the ARM linker script defines ROM_SIZE as PM_SIZE (the full app partition) without subtracting CONFIG_ROM_END_OFFSET...
I have a simple code. send msg to a message queue. and handle the message in another thread. I my old environment ncs2.4.0. I looks works well. // after get msg queue. to...
Dear Nordic Engineer,
Hello!I am planning to develop a 2.4G, BLE and USB mouse. Both the dongle and the mouse device will use the NRF52840. I want to use BLE and ESB simultaneously...
Hello,
For my prject I need to tiggrer a timer start using a pin. I'm trying do do it using PPI but it seems that GPOITE can only create events on input pins. If anyone...
The MCU is NRF54L10, the SDK is NCS2.9.1, and the firmware is updated using MCUboot update mode.
Configuration as follows：
# sysbuild.conf
SB_CONFIG_BOOTLOADER_MCUBOOT...
Hi,
I write this information for the sake of completeness. I don´t need Zigbee2MQTT support from you. Instead, support with the Zigbee firmware is required.
I´m working...
Hello,
I am currently testing a setup combining the nRF5340DK and nRF7002EK using NCS/Toolchain v3.0.0 .
I need to reassign the 8 GPIO pins (including Bucken, Grant, etc...
Background:
Platform : nRF52832 with nRF Connect SDK (NCS) v3.1.0
BLE Roles : The device operates simultaneously as:
A BLE Central (NUS Client) , connecting to an...
While installing the nrf connect extension for VS code and installing the SDK and toolchain I have encountered the same issue multiple times. The toolchain and SDK got installed...
Hardware: nRF5340 DK
nRF Connect SDK: v2.6.1
Description:
I am working on a project where there is a need to transfer a large amount of data from NET to APP core. We...
Hello,
I am working with nRF9160 already since SDK v2.1.2 and with every update there are some functions not working anymore, although not mentioned anywhere in the documentation...
