I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
I thought I had been extremely careful to _not_ brick the device, but apparently I did.
I created a firmware-dfu.zip file, even with appropriate keys, etc. as below.
...
Hi，
During full-device testing, we observed that two devices encounter the MPSL ASSERT: 1, 1519 error after approximately one hour of operation, which causes the MCU to...
Hi Nordic,
On the NCS3.0.2+NRF54L15 platform, we intend to generate pulse widths by controlling P2.1 and P2.5 through timer+PPI. Originally, we planned to use PPI for operation...
Hello,
I have a problem with a tablet that i was planning on using (Xiaomi Pad Pro), my device (nrf25840 dk) is sending data in packets, 4000bytes per packet and its sending...
Hello,
I am working on a custom product based on the nRF9151. I am currently learning RF testing methodologies and setting up a verification plan.
I have read the HW...
Dear all,
I am trying to build bluetooth hci controller for Home Assistant.
I used official example for create usb bluetooth hci controller here:
~/ncs/v3.2.0/zephyr...
Using the options described in ncs documentation for one image pair updates (i.e. not multi-image DFU) appears to be broken in ncs 3.0 and later for upgrading the network...
Hi all,
I'm working with the nRF54L and encountering persistent SAADC issues after short deep sleep cycles.
Setup:
SAADC is configured in differential mode with oversampling...
Issue
When building the Blinky example for the NRF54LM20A with TFM and CONFIG_DEBUG=y the MCU will assert on boot.
When booting an assert is triggered in workspace/modules...
Hello,
I have been developing on a nRF9151DK v0.9.0 for a few weeks now. So far this board is great! However, I have been running some long duration tests recently and logging...
hello, We have a project that uses sound for distance measurement.
When I upgraded from NCSv3.0.0 to NCSv3.2.1, I encountered a problem where the i2s function stopped working...
Hello, I previously learned that the nRF54L15-DK only supports a single antenna for Bluetooth 6.0 channel ranging and lacks a multi-antenna design approach or official guidance...
Hi, We are almost ready with our first board around nRF54H20, only one issue is remaining. We have prepared a sample, that records PDM audio as PCM wave, and stream it over...
Hello,
I have profiled a battery following the instruction of this link nPM1300 EK - Get started - nordicsemi.com .
Since I cannot use the battery NTC, I have placed a...
