I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hi,
I am using custom board (nRF9160) and zephyr V2.6 and I would like to make sure that I understand the ADC settings correctly in the device tree:
channel @ 1 {
...
Hi there,
I have just tried to migrate to a new M2-based mac book pro and everything went OK (i am able to build and run my sw on the target) except that I don't have any...
hi support team，
i was testing smp_svr, i want to add button to my application that once i press the button and reset, the device will stay in mcuboot (serial port mode...
Hi,
I added build a conf to my project which has a prj.conf and select board. But the extension overwrites my configs with cache and extra cmake flags, which i dont want...
Hi there,
I'm currently trying to switch from actively advertising to a carrier wave test. This is the code snippet I'm currently debugging on SDK 17.1.0:
The code seems...
Hello, I use nRFCloud to send CoAP messages, and it's working fine under normal conditions. I am now trying to simulate a network loss, while sending some data. To do that...
I would like to create an ble5 sniffer from my thingy91. I saw that the sniffer is suitable for nrf52840 dongle and nrf52840 DK, and since thingy91 as an nrf52840 board i...
Hello,
I am currently developing a program that uses USB CDC-ACM for USB serial communication.
The USB serial communication is only used when the device is powered via...
Hello
I am developing an application on the nRF9160 SiP, that using CoAP protocol (over LTE) it connects to the nRF Cloud to transmit sensor data, get shadow register configuration...
Hello,
we are using nrf52840 with nrf5 sdk for thread and Zigbee v4.2.0.
We have been experiencing flash memory issues for a while now: https://devzone.nordicsemi.com...
Hello All, I am hoping to leverage Thingy 53's as the sensors (transmitting device) for tracking leveraging AoA. The nRF5340 DK works fine for this application as a sensor...
hi support team,
customer asks me about out 840 usb state, if we have usb low power state as below:
and below is listed in our spec or i n the USB standard ,
however...
Good night,
I am developing a Firmware for a nRF52840 created by RAKWireless RAK4631, with VSCode/Platformio/C++/FreeRTOS, and now I am changing the Architecture from a...
I am currently working with NCS v2.0.2 with toochain v2.0.2
I followed the steps in "How to change a workspace application SDK version" update to NCS 2.6.0.
when i build...
