The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Hi
What is the nRF5340 PDM frequency max and min can be set?
Because below is our microphone frequency spec., we want to set PDM frequency into like between 450~850KHz...
Hello, I’m trying to understand the background of the issue described in nRF9151 DK v0.9.0 Errata . Could someone explain what caused it and, if possible, give an idea of...
Hi
I am trying to integrate a "TMP117" temperature sensor with an nRF54L15 using the existing Zephyr tmp11x sensor driver. The device is detected and initialized correctly...
Hi There,
We are currently developing a prototype using the mRF5340. (MDBT53-1M ) The key is to operate I2S at 192kHz.
Please let me confirm the following:
Is LRCK's...
Hello,
In previous NCS versions I know I have heard the test tone triggered by button 4 on Audio DK work out of the box.
I am currently experimenting with NCS v3.2.1/0...
Hi dear forum members,
I’m working on a firmware project for the NRF52840 that utilizes BLE, DFU, I2C, WDT, some cryptographic libraries, and a few sensor libraries. However...
Hey, wanted to know a few things regarding npm1300 1. Can it handle short circuit of it's buck/LDO outputs? Or we need to have some sort of protection for each buck. 2. If...
Hello,
I am using an nRF54LM20DK with nRF Connect SDK v3.1.1 and I am unable to establish I2C communication with an external DPS368 sensor.
The application starts correctly...
Hello Nordic Community,
We are currently using the nRF52840 DK for BLE testing and controlled BLE interference generation in a lab environment, primarily in the 2.4 GHz...
I have an ICD configured Matter device, using LIT.
I have added the UserActiveModeTrigger attribute and configured it to PowerCycle and ResetButton.
I can commission the...
I am working on an nRF52840 where I need the following outputs:
a continuous 1MHz master clock
a 126 bit serial bit data output sent out whenever a user wants with a...
I have an application with the nrf52840 that was trying to port to nrf54l15 using ncs 3.2.1 but i ran into various issues. I decided to look into some samples that could help...
I am trying to program a Seeed Xiao nRF52840 Sense with a nRF5DK-52832 using the Debug out P20 connector. I am an experienced embedded systems developer (ESP32, ATTiny/AVR...
Hello,
I am developing Channel Sounding related features using nRF Connect SDK (NCS) v3.1.1 and the nRF54L15 Development Kit (DK) , based on Nordic’s official hci_uart...
I'm using custom board based on nrf9160 SoC. After migrating from SDK v3.1.1 to v3.2.1 two issues (but they are likely related) began to happen:
Battery measurements started...
