Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi
I am using the ESB sample and want to use the RADIO_MODE_MODE_Nrf_250Kbit PHY, but I will get not support after requiring:
Can we still use 250 PHY in nRF54L15 ESB...
Hi,
After upgrading from NCS 2.5.2 to NCS 3.1.1, I get quite frequent MPSL assertion errors on a nRF52840. Can you shed some light into what this assertion error is about...
The datasheet list
A25, B12, B26, D2, F2, G1, H2, J31, K2, T2, AG31, as N.C.
I have not been able to read exactly what N.C. implies: It could be: "do not connect", "no...
Hello,
I am working a project that uses the NRF52840 dongle with BLE and UART to communicate to two separate devices while going through temperature cycles. I have not...
My device supports both Central and Peripheral roles. By default, it works in Peripheral mode. When the device connects in Peripheral mode, I want the following behavior:...
Hello Nordic team,
I am working on an nRF52840 project using nRF Connect SDK (Zephyr-based, v2.x / v3.x) and I would like to clarify the official support status of a specific...
Running doxygen nrfx.doxyfile
Per the README.md in C:\ncs\nrf-bm\v1.0.0\modules\hal\nordic\nrfx\doc fails.
See output below.
C:\> C:\apps\doxygen-1.16.1.windows.x64...
Hi there.
we have firmware that was running on nRF5340 MCU. we had decided to migrate to the nRF54H20 MCU because of flash size limitation. this MCU was announced with 2MB...
I am trying to connect to two reflectors and sound only from 1 device so far the connection and soundnig works well for first set of connection and after a disconnectio, the...
I am modifying the Qorvo UWB SDK to add BLE operations. I have posted a couple other topics about different issues..
I have ported my code to the latest Qorvo SDK, They...
With NCS 3.0 and the nRF54L15, even after applying patches, the power consumption anomaly can still be reproduced at the edge of the NFC range. The power consumption anomaly...
We are using zephyr's conn_mgr to manage the network connection. From what I can tell, if I have set CONFIG_NRF_MODEM_NET_IF=y and NRF_MODEM_LIB_NET_IF_CONNECTION__PERSISTENCE...
I want to try the tdm function on the nrf54lm20 dk.
But i have encountered problem in the first step.
I do not know how to add the tdm port and assign the pin.
Whin...
Hi.
We are using nRF Connect SDK v3.2.1 and nRF52832 MCU.
Our current internal flash memory mapping is like below,
mcuboot + mcuboot_primary (application) + mcuboot_secondary...
Mass Provisioning of Nordic BLE Mesh Nodes - Mesh Networks - nRF5 SDK guides - Nordic DevZone
We are evaluating this mass‑provisioning approach. Is there an alternative...
