I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hello,
I'm am trying to use the UART0 bus on the network core at the address:
uart0: uart @ 41013000 {
compatible = "nordic,nrf-uarte" ;
reg = < 0x41013000 0x1000...
Hi,
ubuntu 20.3
vscode + nrf connect
when i creat project from sample code unicast_audio_client, i get the following compiling error message:
* Executing task: nRF...
Hey!
I have inherited a project with a nRF9160 + nRF52480 combination to do LTE and BLE communication.
The setup is as follows:
- nRF9160 using BSDlib @ NCS 1.5.0...
My Peripheral device (nrf Connect SDK, nrf52840) will pair using NFC with an Android (8.0.0) phone. But although the Nordic device shows it is connected (in its UART output...
This press release isn't clear on the exact nature of the LwM2M software stack used on the client side. Are we talking about Zephyr' s LwM2M subystem or AVSystem's Anjay ...
Hi, I am working on a pcb design utilising the nrf52840. I want to use a pcb antenna. I am a hobbyist so It’s very likely I’m misunderstanding something. I am interested in...
Hello,
I am using NRF5SDK V5.0.0. For a sample study, I need to use the bootloader. Can I boot over uart when we install mesh_bootloader_serial_armcc_nrf52832_xxAA.hex software...
Hi:
Currently I am testing to upgrade dual core application on nRF5340 DK, NCS version is V2.0.0.
The two core applications are written by myselves, not based on NCS routines...
Hi
using NRF5_SDK 17.0.2
I'm trying to better understand the DFU process, currently have a large number of questions. But mainly i would like to better understand the...
hello
I am watching this video to operate the nRF9160DK. The PIN number was written on the back of the nRF9160, so I skipped the video to 9:36 as instructed at 5:21, selected...
Hello,
My nRF9160 hard faults (i think?) when issuing a command to the modem, specifically this line:
which then calls ncs function:
This leads to I think is...
Hello, I'm trying to run the OpenThread CLI example on the nrf52840 chip of my NRF9160_DK. I've managed to flash the code on the nrf52 and able to see the Zephyr kernel boot...
I have tried various methods from different doccumentations and I couldn't do so. Can you provides some steps to create a west workspace.
Thanks in advance.
