The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
In order to use "psa_" crypto functions I use "CONFIG_NRF_SECUIRTY=y". I am also using mbedtls for TLS1.2 networking via external WiFi module
By using NRF Security, the...
Hi Team,
I'm installing nRF connect SDK in my PC and i'm using ubuntu for Zephyr RTOS.
When i'm run this command that time error is coming "west init - m https : // github...
I need to use can bus for my application. The chip that will be used will be the MCP2515 can bus ic. For testing puposes i went and tried the CAN sample which is meant for...
I had look on overlay-low-power-conf file and in folder child_image on spm.conf file that UART_SERIAL=n is set. I need to interface a UART device to nRF9160.
1. Is asset_tracker_v2...
I installed the nRF Toolbox on my phone and received data through BLE uart. However, how can I download/save this data on my phone? For example, I send the temperature to...
Hi,
I'm trying to send an data array over ble nus.
This didn't work.
I'm also getting this warning.
I'm doing something wrong, but I don't know what. Do I also...
Hello,
I am making a Firmware for the FCC certification, I must emit at 3 different frequency, 2404MHz (ch37), 2440MHz (ch17) and 2480MHz (ch39) on a nrf52832.
I unfortunately...
Hello,
I have installed the NCS toolchain using the Toolchain Manager app. I am using toolchain version 2.0.0. Here is the error I get when running `west status` :
Same...
I received Thingy:53 and tested it by following the Getting started with Thingy:53 SDK documentation.
The problem arises from the sentence below.
Getting started with...
Hello,
I'm using the LTE Link Monitor v2.0.1 with the nrf9160dk_serial_lte_modem_2022-06-02_880c82db application on a nRF9160.
I'm able to establish the connexion and...
I saw a news report on Nordic's official website that Nordic's NB products have passed the certification of Chinatelecom. I wonder if they have passed the certification of...
Is there a way to add an offset to the nRF5340's reported RSSI to compensate for any front end loss or gain the design might have? This is to get to an RSSI value at the antenna...
Hi,
I'm using HID mouse example in SDK17.02.
After downloaded soft device and the application, I add the device in my pc blue tooth. I can see the battery level normally...
Hi,
I'm looking for a product Bluetooth 5.2 Radio System-on-Chip (SoC) which is of automotive type, and their operating temperature ranges are (-40 to +125)
I'm working on Electronic Shelf Label project using Feather nRF52 with Raspberry pi for server connection. I need to Adafruit Feather nRF52 to receive data from raspberry...
