Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
Hi,
Can mocks fully compensate for C++ standard features.? Is it recommended to write C++ code in nCS project by using these mocks.? What is the support for C++ operator...
Recently I develop products on nRF5340, I plan to make the full BLE stack run in the net-core, and app-core only runs application. It involves data exchenge between net-core...
Hello,
We have a application with soft device on nrf52832 with SDK 15.3 with 60 uA power consumption. It works as it seems for now.
We wanted to add DFU buttonless feature...
Hi,
We were using Nordic HAL for FEM modules to drive our PA/LNA using nRF52840 on zephyr (no NCS). It was only a basic configuration, where the PA and LNA pins were selected...
Hi.
I have a quick question regarding the RSSI Value of Messages sent in a Bluetoth Mesh Network.
So my question is: How exactly is the RSSI Value defined and how does...
I have a few questions about the DFU:
Is it necessary to flash everything together (Bootloader, DFU, APP) for the initial programming when testing buttonless secure DFU...
If you remove power from the beacon right around the time when the LED is going to start flashing to indicate power on, and do that a number of times you will see it will...
I successfully ran the asset tracker with the 9160DK and am able to receive all data correctly, certificates seem to be working, and everything works as mentioned in the asset...
Hello,
We have a large application using ESB to communicate between many nRF52840 devices. All devices are using firmware with SDK 17.0.2. These devices often switch from...
Hi,
I am using nrf52832 DK.
SDK 17.0.2 softdevice S132.
I am using freertos and running nrf52832 as a peripheral.
I want to put nrf52832 in sleep mode.
I am new...
Hello,
I am migrating code from nrf5_SDK_17.0.2 to nrf connect sdk v1.6.1. The board i am using is nrf52dk(nrf52832) connected with adafruit LSM6DSO.
Everything works...
Hi,
How can a specific folder structure can be realized in an SDK project.?
We want to create some folders and follow folder structure in nCS example and develop our...
Hi,
I am currently working on buttonless DFU for my application and I encountered a problem when I generated the .zip file.
In this line
--sd-req, in this case...
I wanted to send 'zdo mgmt_lqi 0x0000' through the serial port to get the 16-bit short address of the ZigBee terminal device, but I found that I did not return the value for...
