Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Hello,
I want to program and debug a custom PCB using the nRF52832 SoC and nRF52 DK. I plan to use this setup:
From what I understand, the GND detect will cause the...
Hi Nordic team,
We are busy testing the throughput of the nRF9160. We are having issues installing the NCS at this stage, and was thus provided with a HEX file of the Serial...
Hi Nordic engineers,
I am using west to build the nRF NCS, my own project which is adopted from samples. Using Powershell (win10) to run west commands as below.
I need...
I tried the "ble_app_hrs_pca10040_s132" example from SDK17.0.2 on an ISP1507-AX and wanted to access the Heart Rate Service to read out Heart Rate and Body Sensor Location...
Hey guys ,
I am trying to merge ble_app_uart code with RTC peripheral code . RTC code works fine when I try it on SDK but after merging with ble_app_uart code it doesn...
Hi,
I have a question about the connection handling when we have two connections to a single smartphone.
The smartphone runs two Applications:
App 1: Acts as central...
Hi,I recently started using a PPK2 board and at first had no trouble setting it up with the Power Profiler Software from the nRF Connect for Windows.
What I realised is...
Hi,
nRF9160 in nRF9160DK with NCS v1.6.0 and master, power consumption measured by PPK2.
With CONFIG_SLM_EXTERNAL_XTAL=n nRF9160 average power consumption is ~7uA after...
My use case is that the nrf9160 is running as a serial lte modem and I have a host controller that is controlling the ENABLE pin. VDD will always be powered so can I leave...
Hi All,
I am using a 3rd Party (Japan) nRF51822 module in a device and it is running a modified Direct test mode firmware without Soft device. Upon testing, it is found...
Hi everyone!
I'm trying to make the NFC work on a custom board. I'm using a BL653 series (nordic nRF52833) and nRF Connect SDK v1.6.0. I am running the record_text example...
I found a similar thread for this issue, but there was no solution... So I want to ask here again here
I follow the video "Introduction to the Zephyr RTOS"
https://www...
We are using a IDE Segger Embedded Studio (SES) for our development with nRF52832.
We need to use IDE which supports IEC 62304 standard.
Our Query as follows:
1. Is...
