I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
My NRF52DK (PCA10040) J-Link always shows SWD speed 1000 kHz, even if I set the speed to 2000 or 4000 kHz. Is it not possible to connect at higher speeds?
I was working with "Debug configuration" for my nrf board on Segger Embedded Studio. It was working perfectly. But when I changed it to "Release configuration", It doesn't...
Hi everyone,
I am using nrf52840 and I want to change the advertising name in bootloader from "DFUTarg" to a custom name on application side.
For unbonded one, I saw...
Hi,
I'm using the provisioning example from the mesh sdk and I have an "ASSERTION FAILED at :0" error when I'm trying to re provision a node that I have provision before...
Hi
I try to understand where does the interrupt proirity for UART is set.
I see that uarte_1_init() is called from uart_nrfx_uarte.c.
uarte_1_init() is declared from...
Hello I am using sdk v17.0.2.
I found a problem with Bluetooth connection while using 'ble_nus_data_send()'.
the system will stop if disconnect the Bluetooth while transferring...
Hello
I'm asking a question because there's a part that doesn't work well while using ble_nus_data_send().
There is a problem sending continuous data to the app using...
Hello
Sorry this is a basic question and I shouldn't be bothering you with this but I have already dealt with a number of issues with Segger so I couldn't resist. - I have...
Hi, I open ssl socket to the server (without certificate verification), and then use an http_client_req() call, to perform the actual http request (with additional optional...
Hello Team,
I am trying to port the example of nRF5 SDK for Mesh to IAR Embedded Workbench for ARM (Dev Kit (nRF52832).
I am using nRF5_SDK_17.0.2_d674dde and nrf5_SDK_for_Mesh_v5...
I'm testing the Serial LTE Modem application on the nRF9160DK with the LTE Link Monitor. I want to use the DK as a UDP client to send data
to my remote server via UDP over...
Hi,
I am working with a custom board that has an nRF9160 SiP (B0). I am using SDK v1.6.0 on a Windows 10 machine. Modem FW is v1.2.3.
Our device uses GPS periodically...
Hello all,
I'm trying to use P0.05 (AIN3) as output, but it does not work.
in file .dts is used as: rts-pin = <5>; status = "okay"; of uart0, I have to change this config...
I'm evaluating feasibility and developing a Proof-of-Concept for a client using the NRF9160 + NRF52840. This is a second generation product where the client wants to evaluate...
