The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
The reference design for the nRF5340DK uses 0201 components for the matching network.
Would it be acceptable to replace the 201 matching network components to 0402 parts...
Hello NRF,
I have a custom board with NRF52832, and exposed the SWDIO, SWDCLK, GND, VDD, RESET pins for programming the board through the NRF52-DK board.
I started with...
Dear Nordic,
I have some issue with SPI interface (MCU as master, BL654 as slave)
I can see correct signal from oscilloscope, and SPI mode and CLK is config correct...
hello,
i am using nrf52840 with sdk 15 and using ble_app_blinky example i want to advertise my device as i beacon(only mac address) without any name what i did until now...
We have generated a .hex file to be programmed to the external QSPI flash on the QSPI bus of an nRF5340, using the same MX25 part as used on the DVK (8MB/64Mbit) but with...
Hello Team,
Need urgent support for the nRF52840-DK.
I want to develop a program for the above mentioned kit for green power zigbee communication. This DK will communicate...
I was testing 9160 power consumption, the specifications says it is the minimum consumption current 7µA, but when I test on the DK board, the minimum current is 2ma, my test...
Greetings, I designed custom board using nRF52832 and sht20 temperature sensor. I defined sda and scl pin number of sht20 in pca board file (pin number 23 and 24). 4.7k pull...
Hello,
I want to test cold start performance of GPS on the nRF9160 DK using the gps example from the SDK. If I run the example unmodified from the sdk, get a fix, power...
Hello!
I am working on a project where we want over the air updates for the finished product. To make that possible I implemented the buttonless DFU and it is working great...
By following this post , I had some issues.
When compiling nrf_ppi.h:
1) For channels 10, 11, 12, 13, 14, 15: 'PPI_CHEN_CH10_Pos' undeclared here (not in a function...
Hello !!
I have custom board on nrf52832 having 10 buttons which is pull down by default. I have achieved 22uA after modifying the ble_app_beacon example to broadcast when...
I am writing a program by moving the contents of twi_master_using_nrf_twi_mngr based on the ble_app_uart project.
The source code is as follows.
Please tell me how...
Hi, 1- I have worked on ble_app_template(As Peripheral Only). Now, what changes I should make to gain max range? Any specific changes for long-range? 2- Here is my code. I...
