Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi
I have developed a PCB that will be used to control some sensors. The pins NFC1 and NFC2 are intended to be used as GPIOs. However, the default processor settings configure...
Are there any ways/workarounds/configurations to drive P0.9 on nrf52840 as an Input/Output instead of just being NFC pin.
Technically we should be able to drive this pin...
Hi,
I'm using an ISP2053 (nrf5340) chip on a custom board and debugging using the nrf5340dk. I'd like to use P0.02, P0.03 as part of an SPI bus.
I set up a simple experiment...
Hello everyone,
I've recently migrated a code from nRF51822 to nRF52832, thus I started using fds library to manage flash storage from SDK v17.1.
The issue I'm having...
So i have a custom nrf52840 board that i'm working on with SDK 15.2
I want to use the NFC as GPIO.
According to the docs i need to set in the sdk_config.h CONFIG_NFCT_PINS_AS_GPIOS...
Hi,
I'm developing an Android app that will be used on Samsung Galaxy Tab devices only in which the user can connect, through BLE, to another device, which is a module added...
Hi
We have a product that uses a nRF5x Soc. Is acts as both a central and peripheral. The central part connects to a pulseoxymeter, and the peripheral part allows an app...
Dear Developers,
I am in the process of implementing the nRF9151 and would like to inquire about the necessity of the blind vias in its pad. Like on the nRF9151-DK.
Are...
SDK: nRF Connect SDK 2.9.0 with VS Code
SoC: nRF52840. nRF52840-DK for development.
We are currently using USB to output logs for debugging. For production, we disable...
Hello, I am following the official tutorial ( academy.nordicsemi.com/.../) to enable DFU over USB function on both nrf5340DK and thingy53. I am using sysbuild for both board...
Hello Nordic Team,
I am working on measuring battery voltage ( 3.7V ) using a voltage divider ( 220KΩ and 100KΩ ) connected to AIN2 on the nRF54L15 DK.
However, I am experiencing...
My device is a peripheral and during bad RF conditions I would sometimes see a BLE_GAP_EVT_CONNECTED event but the central never receives a packet from the peripheral so it...
Hello,
I'm running both central and peripheral roles for BLE on Zephyr, along with UART and some GPIOs.
SDK: 2.6.2
The project includes MCUboot, supporting DFU...
We are trying to max out the wifi throughput via nRF7002 when connected to SPI4. Currently we only achieve around 6.3Mbits/sec (TCP Upload to peer).
When measuring the SPI4...
