I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
I'm working with NSIB (nRF Secure Immutable Bootloader) and trying to manually sign an application image that is built separately — without using SB_CONFIG_SECURE_BOOT_APPCORE...
I have a custom board that uses nrf52832 and I would like to add FOTA support using Bluetooth.
When I build the code using the nrf Connect inside VS code, it creates a DFU...
Hello guys good Morning,
I am currently studying the examples in the Nordic Dev Academy. I am in lesson 5 from the "NRF Connect SDK Fundamentals", and I managed to toggle...
Hi,
I'm attempting to restore my Thingy91x to communicate with my instance of nRF Cloud (I had removed the certificates previously to test out the connection to another...
Hi,
I am using a custom nRF52832 board with multiple ADC channel readings sequentially. I am trying to read thermistor (NTC) value on channel 7 and not getting accurate...
Hi community,
I'm using the following setup:
nRF5340DK
nRF Connect SDK v2.6.0
B0 , upgradable secure MCUBoot, and application
Statically defined partitions in...
Hi,
My requirements are:
My essential need is a one-to-one connection between central and peripheral .
But when my central receives the specified command to start scanning...
Hello there, this is my first post here.
I'm facing a wall in my project development.
Here is the issue, so during start up of the NRF52832 I see a high current draw for...
Hello, I need your help about BLE channels. Currently, I use only the primary channel 38 for advertising data but, when the data are sent, I don't have the information of...
Hello,
I am currently working on connecting a Thingy:91x to a Cube Orange autopilot (Pixhawk 2.1) in order to receive telemetry data over UART using the MAVLink protocol...
We need a parter to develop the Thread terminal base on Nordice nRF52840, the project will be design in China and produce in Germany. Is there any reliable company could provide...
I noticed that through apply_old_config.h configuration values like NRFX_CLOCK_ENABLED in sdk_config.h simply get overriden by the old CLOCK_ENABLED, so that there is no point...
The scanner can be informed of the synchronization information as soon as it receives an ADV_EXT_IND PDU, and then it can later scan only AUX_SYNC_IND PDUs. at this point...
I am using NRF52832 Custom Board and Have to implement deep sleep for 1 minute and have to limit the current consumption to a very minimal value during the sleep cycle I have...
I am trying to get the J-Link RTT viewer working with the Sysbuild Peripheral LBS Sample from the BLE FOTA DevAcademy lesson . I need the SEGGER J-Link RTT viewer working...
