The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I have tried the below in proj.conf.iam using NRF52833 DK in VS CODE(NRF SDK Connect extension.Iam trying to receive data through gatt protocol,but it is not receiving more...
Dear Nordic Support Team,
I am currently working on a project using the nRF5340 and would like to implement BLE Channel Classification, similar to Adaptive Frequency Hopping...
Hi
i want to create a bluetooth beacon which should get input in gatt(UUID,name,major,minor..then it should be advertise with the new UUID.
Iam configuring it with ibeacon...
Hi
I have tried to reproduce the 2.7µA current consumption stated in the datasheet. This webinar shows that the UDP sample reaches 2.7µA on the nRF9160 evaluation kit. However...
Hello Nordic! My question probably a simple one but I'm a novice so there's it. I'm looking for a way to get a GPIO port state that was at the moment of GPIOTE event triggering...
Dear Nordic Support
We have an existing Project that uses the nRF9160 SoC and builds with toolchain v2.4.4 and SDK v2.4.4.
The project basically runs with the nRF9160...
Hello,
My DK stop working as programmer suddenly.
the VDD power is normal with 2.9V and the V5.
Try already to power on with reset button hold.
blinking is not Consitency...
Hi Support Team
We meet an issue like the screenshot below when I program nRF52840 chip via the SES.
The SES version is v5.42a.
The J-link we used to program is...
hi:
asset_tracker_v2\src\modules\led_module.c
I only found the file that calls the LEDs, I didn't find the specific initialization and control code? Can you tell me how...
Hello everyone, a pleasure and very grateful to be able to write in this forum.
I am trying to program a Nordic BLE device so that it does not appear in the pairing list...
Hello, I am developing a board using the nRF52840 QFN48 and powering it using a 3.7V single cell LiPo battery. Since the battery voltage is stepped down to 3.3V via an external...
Hi.
I would like con build nrf Connect OT COAP Client and Server on a zephyr 4.0.99 / toolchain: zephyr 0.17.0
I have downloaded nrf sdk 2.9.99
running:
west build...
Testing the RADIO TEXT example on 52811.
1. 52811 is not a supported target - so I must select all targets then the unsupported dts (nrf52840/nrf52811)
2. I add a Build...
