The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Hello,
My board contains nRF9160 and nRF52840. The nRF52840 is a HCI controller (based on HCI lpuart example). nRF9160 communicates with nRF52840 over UART. I want to perform...
Hi, in our project we use nRF5340 to control some externanal peripherals as flash mem through SPI and also we need BLE comunication.
The case is if whe allow the config...
Hi, I am trying to use the DECT NR+ sample from the 2.7.0 nrfconnect sdk but I can't seem to get the following to work in the prj.conf:
the results of my build give...
Is there a way to convert the firmware for the nRF Connect RSSI viewer to work on the nRF21540DK. I imagine it isn't too difficult, since it is essentially the nrf53840 but...
I have customed a board based on nrf54l15.
Then I built the matter light_buld demo with target 'nrf54l15pdk_nrf54l15_cpuapp' and burned the file "merged.hex" into my custom...
Hello,
I'm using "Bluetooth Mesh Light switch" code which i have modified to act as a gateway. Where it periodically collects data from lights. After receiving data from...
Can the VDD PIN of 4L15 be used to detect the ADC voltage? VDD is powered by a dry battery (3.2V~1.8V), LED+ is powered by 3.3V, LED- will be connected to the I/O of the 54L15...
Hi,
I would like to add MCU boot hardware downgrade prevention in my project.
So i had the following config in prj.conf
Then, when i flash my board i get this error...
I am trying to configure himax camera and stream to app but unable to get image, rather when I am using nrf app to see data i am getting data something like this:
'40-13...
I saw a few questions related to this but nothing I found quite answered my question. We are experimenting with the nRF9161 DK, and we need to securely identify which device...
Hi there, right now I'm working with an application that allows me to collect data via UART from several sensors (two), and I also I have a SIM module that allows me to communicate...
Hi,
I'm trying to build the " tx_rx_non_blocking " sample (ncs2.70, nRF52840dk) but get the following error message -
C:/devtools/nordic/ncs/v2.7.0/modules/hal/nordic...
The CPU runs the main thread every 3 seconds, and for the remaining time, it enters the idle thread. However, after entering the idle thread, it doesn’t save power.
But...
Hi guys,
we are planing to use the nRF52820 as BLE proxy to UART/SPI. It shall receive data from a host controller via UART/SPI and forward it via BLE to a smart phone....
