Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
Hi there,
I am considering using one of the npm1300 LDOs to supply 3.6V to the battery backup pin of a uBlox MAX-M10 module using a 100uF capacitor as energy storage for...
HI,
I am using an nRF52840 DK as a Bluetooth LE sniffer and have followed all the steps described in the official documentation .
In Wireshark, I can see “nRF Sniffer...
Hi Nordic team,
We have used shell example of Zigbee sample to connect to an end device. We want to extend the FEM feature of nrf54L05 for this example. We have already...
I want to implement dual-mode operation of LORAWAN and BLE, but when using the SoftDevice, the interrupt on the LORAWAN DIO1 pin does not trigger. I suspect it is being blocked...
Hi,
I have a question after using the DMIC example on the nRF5340:
how do I adjust the PDM clock frequency to 1.28MHz, or how can I achieve this by changing the value...
hello Nordic
i am working with nrf 52840 and 52832. using ncs v2.8.0
i am saving a coredump to flash partition and i am using gdb server - client to try to parse the coredump...
Hello,
I'm migrating an ANT+ BPWR application from **nRF5 SDK** to **NCS v2.5.1** but cannot install the sdk-ant module.
**Background:** - Previously used nRF5 SDK with...
Hello,
I send a ticket because I have an issue to access and write files to a SD Card with NRF54L15DK and 3.1.0 SDK and toolchain.
Can you help me please ?
Here is my...
Hello,
we are trying to run Gazell samples on the nRF54L15-DK, but the protocol & board combination doesn't seem to be supported by version 3.2 of the nrf Connect SDK...
We would like to synchronize several Nordic thingys 53. The Approach is to send two timestamps from a central to them (peripheral) via Bluetooth Low Energy with 100 ms delay...
Hi
I try to start with ST7789 display on nRF54L15 and there are bus fault after add LVGL library. The project is building correctly, but stop just after leave bootloader...
Hi,
I accidentally opened and subsequently programmed the PPK-II in Bluetooth Low Energy module startup. The programming didn't complete but resulted in an error. Now...
We are using the nRF9151 with modem firmware v2.0.4 and would like to perform TX RF testing on NTN bands 255 and 256.
TX RF testing is currently initiated using the modem...
