Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
basically, I want to use dm feature in connection-oriented communication. not in connection less, and I want to connect 1 central to 4 peripheral and measure distance.
Can...
nRF Conncet for Desktop v5.0.0
Hello,
I have some trouble to update the Toolchain Manager of version later than v1.2.6. The download fails. However, I can download the...
Hi,
We are working on a project using the nRF52832, which utilizes UART for a QR-code sensor, I2C for an OLED display, and SPI for external flash memory.
We are at the...
Hello.
I am trying to write protect the Flash area using nrf52840's ACL peripheral. I tried to perform the same process on the main processing side by referring to nrf_bootloader_flash_protect...
Hi friend,
I use SDK16.0, and the version of softdevice is S140 V7.0.1. Can I advertise a special data? like 0x08,0xff,0xa6,0x02,0x33,0x09,0x55,0x00,0x0c. 0x08 is packet...
I am looking for to buy(I don´t have a 3D printer) a enclosure to protect my nRF52840-DK. It is not a good practice to handle because probably soon this practice will damage...
Hello, I just receive a nRF9161 Development kit and I'm completely new to both nRF9161 and Zephyr.
I want to start an evaluation project based on the nrf9161 lwm2m client...
Setup:
windows 11
VS studio code
Toolchain and SDK v2.6.1
hardware: nRF52840DK / PCA10056 (bought June 2024)
Using sdk/zigbee-Template as the base for the project...
Hi all,
I'm using an nRF5340 DK and I want to build a simple project that plays a sinewave to an i2s DAC (MAX 98357A, perfectly working on other development boards I have...
Hello,
I found that after bonding, I could still connect to another board that had burned the same code.
Here is all of my code related to pairing and bonding.
Central...
Hello,
I tried to find information about using the QSPI with external flash on nrf connect SDK.
My goal can be split into two parts:
1. Use QSPI with external flash...
Cant Flash Thingy52 on VS code after flashing once and also cant read sensor values of thingy on serial terminal. How can i flash on thingy52 smoothly like flashing other...
My programm uses both the non-secure world and the secure world, with the non-secure-world largely just calling functions inside a custom partition of TFM in the secure world...
Hi,
I'm working with a nRF54L15 within the nRF Connect SDK on Zephyr. I need an array which retains its content through soft resets, so in another RAM section than the...
Greetings,
One question on the nRF9161/51 capabilities: is the 3GPP Rel-14 LTE-M Cat-M1 larger UpLink transport block size (TBS) of 2984 bits supported (instead of 1000...
