I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
I wanted to check if iOS 18 supports extended advertisements on coded PHY. I am not concerned with the advertisement payload limit but the increase in range that is possible...
I tryed to use the callback function provided by mgmt to hookit, but after including the header file` zephyr/mgmt/mcumgr/grp/img_mgmt/img_mgmt.h `, it prompted that "mcuboot_config...
Hello everyone,
I am currently facing an issue when trying to read data from a block of a Mifare 1K card. After debugging, I found that my program fails to authenticate...
We want to enable 2 way communiaction between Our Nrf9160 devices and server using Websocket secure. We used this as the starting point. We removed anything related to IPv6...
Hello,
We would like to interface an external PSRAM with nRF5340 MCU.
We didn't find any refference on how to do so.
So, my question is it possibel to interface...
Hello,
I'm using nRF9160 and modem firmware version 1.3.6.
I'm using %XRFTEST command to measure RX power received by modem. Command documentation can be found here: https...
I have been through the devacademy lesson on custom boards and am using the nRF53 so have used the custom board for multi-core approach. The example uses the 9151 which has...
I'm trying to add MSC functionality to my project, but I'm encountering the following error:
To understand the cause of the error, I tried creating a new application from...
Hi Nordic Team
We develop a sensor node for a customer based on nRF5340. For now I use a nRF5340DK to do my tests with NCS 2.8.0 (using VS Code).
Based on examples, I...
Good Day,
We have an ongoing project that uses an RP2040 MCU (with FreeRTOS) and we need to add WiFi capabilities to it. It needs to be dual-band and fairly high throughput...
Hi all,
I'm currently working with the nRF52 DK (nRF52832_xxAA_REV3) using the nRF5 SDK version 17.1.0_ddde560 and the IAR Embedded Workbench - Arm 8.32.3 IDE. I'm facing...
Hi Team,
I just want clarity on 2 points related to accuracy of nRF9151 GPS.
1) As shown in datasheet, "Positioning accuracy (CEP50), periodic tracking" is 3.4m. So that...
Description: I am encountering an issue while testing the watchdog functionality. When I intentionally hang the system for longer than the configured watchdog timeout period...
Hello,
I'm new to software development so apologies if this is a simple question but I can't find a straightforward answer for nordic connect sdk on vs code.
An IC I...
