I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Following Setup:
1.) Building light-switch-app from original https://github.com/project-chip/connectedhomeip Repo for nRF5340 from command line with nRF SDK v2.1.0
2...
Hi,
We are close to going into a certification process but before we start we need to be sure we are not missing out on your recommendations with regards to EMC performance...
Hi,
I get the error like below on the Linux XFCE 64-bit platform (Pardus 21.2 distro latest version). It works fine on Windows but having a problem on linux. How can I solve...
Dears,
Currently, when working with the nRF52833dk, I found some weird behavior.
I tried to run the blink example in nRF5_SDK_15.3.0_59ac345\examples\ble_peripheral\ble_app_blinky...
Hello. I want to check "Airlog" or "hcisnoop" with nRF5340 LE audio EVK. The current development environment is VS Code. I also have a USB Dongle, but I don't think I can...
Hi,
I'm using nrf52840 with softdevice s140_nrf52_7.2.0 and I'm adding new characteristics to the ble_nus service. I've added the new handles for the new characteristics...
It appears that after a few seconds and sometimes after a few minutes sleeping threads do not wake up, even though the UART shell and BT NUS are working. The only service...
Hi,
I am trying to configure GPIOs with a custom DTS file, for initial bring-up and testing of the PCBA prior to higher-level development. During compile, I am getting a...
Hi, we have a use case where the central might need to re-bond with our peripheral (e.g., after choosing "Forget this device" in phone settings). I have learned that setting...
Hi
i am working on the nrf5340_dk for making as a controller through the hci_uart build.
can i know the gpio connection mapping on the board?
regards,
Achyuth
Hi, I'm currently having a problem with the uart peripheral.
I have an STM32 MCU connected to the NRF52840. In this case, the NRF acts only as a "transceiver".
Whenever...
I have my own code for handling pin interrupts using the NRF_GPIOTE EVENTS_PORT interrupt. I had some issues with this years ago when I was using the nRF52832 chip, which...
Hi,
is it possible to configure the hci_uart example from NCS in a way that the FICR device address of a nRF52840 is used as public device address? I cloned and compiled...
Hello,
We are trying to get the NVS example on our nrf9160 DK running. The build and the flash process looks fine but the application won't boot. Not even the typical...
Hi,
I bought a second nrf52833-dk. After I program my code on it, I can't debug or read the code because read protection is on. This is strange, because I didn't program...
