Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
I am having a lot of trouble having to change my dt files and receive errors every time i try to run a basic sample for the NCS . Is there any 'How to' that i can refer and...
I hope to add custom data to the ASK package returned to TX in the ESB application. How can I add it in the input? How should the tx side read the custom data.
Hello,
I received the Thingy53 as part of the Hackster IO contest. Right now I am having problems to flash it through the VS Code. My VS Code instance is unable to detect...
I have a thingy 53 that I got from the HacksterIO competition, I'm trying to program it using the Programmer application from the NRF Connect Desktop application. I open Toolchain...
Hello,
I am trying to connect PS4 controller remote with NRF52840 so I can get command from remote and execute require action but not able to detect PS4 MAC in nRF52840...
Hi There,
I have been looking for ways to have three channels of a hardware timer with the NRF52840 generate a compare interrupt at different time intervals, my understanding...
I got MCUBoot running using signed images. Now I want to enable encrypted images using the build tools, but how? I've found this pull request: https://github.com/zephyrproject...
We are looking to move from STM32WB55 to Nordic.
I am use to developing firmware in the NXP and STM environments, looking at documentation for register address or examples...
I am trying to use the experimental task manager of the nrf52sdk, version 17.1.0. I've come across what I would call a bug, but there might be a reasoning behind it, so that...
I have
Hardware: nRF52840 DK - 1 nRF52840 Dongle - 1
Software: nRF5 SDK Mesh - v5.0.0 nRF5 SDK - v17.0.2
I want to program Mesh Serial example on nRF52840 Dongle.When...
Hello everybody.
I am developing a BLE application in which I am using WDT every 12 seconds and a RTC interrupt every 10 seconds to send some information.
When you press...
Hi,
We are using nRF5340 and we are migrating to v2.0.2 NCS sdk from v1.9.1.
In our design, the SPI MISO pin is P0.10. From the dev zone tickets, I found that this P0...
Hi,
I'm trying to send I2S data (~ 16 kHz, 24 bits) via BLE using the nRF52 DK and the nRF5 SDK 17.1.0. After I get the data from the I2S driver (by specification, they...
Hi!
To measure the voltage level of a coin cell CR2450 can be done in different ways.
You can use the comparator, the low power comparator or the ADC.
I wonder which...
Hi, The getaddrinfo() function returns the same IP address for www2.domain.com and domain.com, namely that of domain.com while they are running on different servers and have...
