Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
in the ticket here it was reported that the fix for the external flash problem was supposed to be fixed in 2.1.0.
Is that still the goal ?
Can i kindly have an estimation...
Hi,
I'm using nRF52805. I need to advertise BLE continuously according my application but also have to reduce power consumption because device is battery operated.
Currently...
Hi,
today I faced a rather strange problem when trying to restart the SAADC.
Bit of context: a requirement for the product I'm developing changed and the device now must...
Hello,
Can raw data be published via MQTT with SLM 1.7?
In later versions we have done this by entering data mode, which we see is not implemented here.
Is there another...
I'm using the nRF52832 in an energy harvesting application, where I need to cold-start the device and set a GPIO output high in under 50ms in order to latch the power supply...
When using AT command to send data, the baud rate is set to 9600, and the two modules are connected at different temperatures, and the data is sent through the serial debugging...
Hello everyone
The company I work for produces an nRF52840 based dongle.
We also have a bootloader which is a modified sdk example.
We need to save some important data...
I'm trying to install nrf-command-line-tools_10.17.0_amd64.deb on an up to date Debian 11, but dpkg always fails with this error:
# dpkg -i nrf-command-line-tools_10.17...
Hi there,
We appear to be having the same issue as described here and here on a nrf9160 DK. There was no clear changes to hardware at all. LED5 suddenly does not seem to...
Hi Nordic support,
I have been evaluating the nrf5340 audio DK and recently run into a build issue with the example application. I have been able to successfully build...
The following error occurred after BLE APP connects to nRF52832 device. How can debug this issue?
<error> app: ERROR 4 [NRF_ERROR_NO_MEM] at ..\..\..\..\..\..\components...
Hi.
I'm trying to include MCUboot in my application following this guide but I get this error:
I'm using version 1.8.0 of the nRF Connect SDK with a project using spm...
Hi,
I notice that the Power Profiler II (nRF-PPK2) connectors are polarized. I'd like to make special cables for my test fixture. Can you tell me the manufactures P/N for...
Hello all,
I am using the PWM and TIMER drivers on the nRF52DK board among other drivers like TWI and I get this error when trying to compile, eg. today
It can be seen...
