Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
From various pages I copied together this code to read the reset reason:
However, I believe most of those pages were for nRF5 SDK. (It's not always clear.)
Is this still...
Hi Nordic
I used the nrf_gpio_cfg_sense_input() API to initialize the GPIO4 for waking up nrf52832 from system off mode, This IO could wake up nrf52832 successfully, but...
These two func:"softdevice_ble_evt_handler_set "
and "softdevice_sys_evt_handler_set" suggests that there are two categories/sets of events grouped into system & BLE.
...
I'm a user of nRF52 DK with S132.
I want to modify the event handler in the example application code such as ble_uart_c.
Where can i find the full list and description of...
Hello
Can I use the LORAWAN module with NRF52833? if yes, is the LORA gateway also required to send the data to the cloud, or can it be done directly without a gateway?...
TX :52840
Software version：nRF5_SDK_16.0.0_98a08e2 hardware version：
RX:52820
Software version：nRF5_SDK_17.1.0_ddde560
My test method: send 60 bytes of data through...
Hi:
I use sdk:nRF5_SDK_17.0.2_d674dde and NRF52840.
Reference examples:nRF5_SDK_17.0.2_d674dde\examples\peripheral\uart
PC connection RX-pin20 and TX-pin22, PC sends...
Hi,
We are looking to purchase the nRF52832 SoC. The data sheet says it supports a data rate of 1Mbps when the receiver sensitivity is set to -103dBm. This data rate is...
I am experiencing a strange behavior with SES 6.32, using GCC and I wonder if I should choose a different compiler.
COMPILING THIS PART OF CODE (I added line numbers for...
I want to add wifi connectivity to asset_tracker. It is required that MODEM is turned off. The program flow need to change so that instead of Modem, wifi Module is tried first...
Hello,
I am trying to read a 32-bit value over BLE but the value displays as 8-bit on nRF Connect. In my code I am sending it as an int32. Why does nRF Connect only show...
Hi There,
I have almost done the project, I used nrf52832 as central(master) and nrf52810 as peripheral(slave).
i use the blinky example and everything working fine. I...
Hello,
I am using nRF52840 and I currently am working on a application where mostly I am using central functionality (BLE connection and exchange the data) along with cellular...
I'm willing to use the 5 claused licensed code for the parts that only work with nordic hardware, but the partition manager isn't actually necessary. Is there some way to...
