Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
I am having trouble setting up DFU over BLE in nRF Connect SDK. I am using NCS 1.9.1. I have followed these instructions with my own project on both the nrf52840 devkit and...
Dear All,
We are developing a device based around nRF52840 on a rigid-flex custom PCB that is mounted inside an anodized aluminum cube with one face covered with plastic...
Hello, I'm trying to get an LPN to unprovision itself based off of an external command. I tried to base it off of the examples so I simply call: However after the reset it...
Hi,
I have my device based on the nRF52840, we have manufactured some equipments and we have created our own application to manage connection. Everything is working fine...
Hi all,
we recently had a problem with couple of our boards based on Raytac MDBT50Q-1MV2 (nrf52840 + osc. + antenna). We base our app on Zephyr. After programming some boards...
Hi, I've been tasked with doing some development on the nRF24LE1F on one of our legacy products that was designed many years ago! I'm in process of converting the code to...
Hi,
I'm trying to use UART1 for console and shell, for example to be able to log messages on VCOM0 linked to UART1 of my nRF5340 DK board. The example that I'm testing is...
Hi Nordic team
Customer Delta was running a street lamp project.
For AWS FOTA, they applied a AWS account and firmware update already can work.
However, it looks like...
Hello,
I am developing FW on NRF52840_DK for a BLE Peripheral as a Reader.
Reader to Mobile App Tx size is 32 bytes
Mobile App to Reader Rx size is 133 bytes.
When...
Dear Bluetooth Mesh experts, The firmware contains a proprietary message that sets a node's parameters and returns 100 bytes of data. The Android app sends it as an acknowledged...
Hi
I've configured Zephyr to run BLE host on cpuapp and BLE controller on cpunet, and using RPMsg to communicate between them.
When I call bt_enable() from the app core...
Hello,
I was wondering if there is a way to extract the "Device name" from the scanned advertisement data published by a model on a different node. I want to display the...
Hello ,
We are attempting to use the QSPI driver with an MX25 with 2 i/o lines instead of 4, essential SB 10 and 15 on the nrf52840 DK have been cut. However I am not...
Since the APP CPU memory is mapped at 0x2000.0000 in the perspective of the NET CPU, we understand that r/w access is possible for data. Is it possible for the NET CPU to...
I have a vendor model bt_mesh_model_op defined as follows
const struct bt_mesh_model_op _admin_model_ops [] = {
{ BT_MESH_MODEL_OP_3 ( OPCODE_SET_UNACK , VENDOR_ CID...
