Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
I am designing a PCB including the nRF52833, and I just wanted to confirm the requirements for the vias-in-pad for the signals on the inner row of the aQFN footprint...
`Hi There,
For nRF5340 board, If I want to update encrypted net core bin file using FOTA, then what are the options to achieve it.
I have created encrypted image manually...
I am just wondering if Nordic is actually working in their R&D lab on the nrf9160 update with an LTE cat 1 SIP. I think the current IoT application development requires higher...
Hi all,
I'm using an nRF52-DK for testing the connections of pressure sensors (BME/BMP280), I tested first with arduino, and then I'm using the same code with Platformio...
Working on 52832, with SoftDevice S132, SDK 17.0.2 Our boards have external 32MHz crystal as the source of HFCLK.
Our application samples the ADC periodically using the...
I am in final stage of pre-production code and would like the associated indicator LED to go to OFF
when the coordinator is lost or powered down. I can detect it joining...
Hello!
I am struggling to configure a quadratic encoder with the nRF52840. As far as I know, the code should be working. However, when the encoder rotating, the terminal...
Hello there!
We are using nRF51822_xxac SoC with nRF5 SDK v12.3.0 and S130 Softdevice. We are kind of obliged to stick with nRF51822 because nRF52840 SoCs were out of stock...
I allowed some Windows10 updates to go through earlier today, and now I can't get my code to build.
I've even gone back to some previous versions that worked yesterday and...
Hi,
NCS for Windows VSCode have update to last,
TERMINAL panel can't copy one line,
and can't clear all.
Suggestions for improvement.
thanks
Best Regards
Toolchain: 1.9.1
modem fw: mfw_1.3.1
PC OS: windows 10
Terminal software: Tera Term
SIM card: AT&T (North America)
in the modem shell example code, in "prj.conf...
There are multiple issues like https://devzone.nordicsemi.com/f/nordic-q-a/81793/jlinkarm-dll-load-failed-on-m1-mac which are basically just « resolved » by saying « these...
Hello,
I'm trying to figure out what I am doing wrong (or what I misunderstood) about the bitrate.
According to my benchmark, it takes 1.42ms to send 128 bytes using ESB...
Hello, I'm using SFH 7072 Heart rate sensor with nRF52832 board , But i'm not getting actually heartrate, i'm getting like a 6-7 digit output , for that which calculation...
It is written in the datasheet that if i try to receive bytes more than the number i put in the maxrx register "incoming bytes will be discarded" does that mean all the bytes...
