Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hello,
I am working on application using nrf52810 SDK version nRF5_SDK_14.2.0_17b948a
In my application i need to read characteristics value, so after following tutorial...
i use the zephyr 3.0.9.i use direction with nrf52833 or nrf5340 in RX.The tx is nrf52833 with nrf of NCS,ITversion is zephyr 2.7.9.The default is 2us AOA. I want to use 1us...
Hi,
I have installed Segger Studio for ARM v6.22a.
I have also installed the SDK5 version 12.3.0.
I imported the IAR project project ble_app_start_notification_pca10028_s130...
Hello,
I have been working with a BLE custom board project for a few months and the product requires buttonless DFU feature. The bootloader that I initially used was derived...
System details:
Board: Custom
Chip: nRF52832
PCA Number: PCA10040
SoftDevice: S132
SDK: Version 16.0.0
I have been building a custom nRF52832 device for a...
I'm trying to use the LTE Link Monitor, but when I open the app, the log shows: Failed to get the library versions: JLINKARM_DLL_COULD_NOT_BE_OPENED (Origin: "Failed to get...
sdk: 1.6
modem fw: 1.2.3
Hi,
Been trying to test mqtt every which way and not getting any success with mqtt keep alive longer than 30 minutes, the mqtt connection...
Hi All,
I have encrypted app_update.bin manually and perform FOTA with single stage bootloader and it is working as expected.
Now I have enabled Two stage bootloader...
i am working with spi example but the clock appears as shown in the following photo i do not know why it is generated like this and i need help to configure it to work as...
Do you have an updated schematic for the latest nRF52-DK development board? The board I have from July 2022 (reference # 0365RUBR) has some differences compared to the online...
Hi there,
A couple of weeks ago, I'm facing the issue that my nRF52840DK board is not visible and led5 is flashing rapidly. I reflashed the bootloader, j-link-ob-sam3u128...
I added some functionality to asset_tracker_v2. I used two pins of Nordic chip for following purpose: 1. Detect BMS, pin as Input 2. Reset BMS, pin as output. The pins overlay...
Hi,
I'm a newbie of microwave board design, after many research I finished our 2.4G USB Receiver board which use the nRF52840-QIAA. But I still want some advice of the RF...
Hello,
My setup is UDP sample and PPK2 for power measurements. I am trying to figure out the best settings that are available with eDRX set to <= 20.48s, and preferably...
