Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
I am connecting my nrf9160 based system to the nRF Cloud and sending data from it.
I got the cloud to show the RSRP values that I sent it through the following JSON...
NCS 1.8.0
Modem FW 1.3.1
For other products I've worked on with cellular modems, we would add in back-offs to the firmware in the case we failed to open a PPP session...
Hi,
I've been playing around with the attached low power mode example. It seems to be written around the nRF SDK, but I am attempting to build and flash from within VSC...
Hi Team,
We are working with nRF52832 and nRF Connect SDK v1.8.0. Our application needs to sleep (power save mode) for 5 minutes and every 5 minutes it should wake-up...
Fota used to work fine in SDK v1.7
No I have moved to SDK v1.8.0
I don't believe my software has changed, however I am getting an error when running as follows:
Any...
Dear Nordic Engineers
Our customer use nRF9160 to develop a tracker.They found that their programs were relatively power-hungry.They tested the serial_lte_modem example...
Hi there!
I am trying to combine the SPI and ble_app_uart examples.
However, when I add the SPI part to the uart, it shows this:
I believe there is some problem...
In the demo in test \ v1.9.0\zephyr\samples\subsys\usb\audio\headphones_microphone , I found that only dual channel 16bit 48Khz audio can be recognized on the PC. the product...
Hi,
I am using ble_sdk_app_hids_keyboard example:
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v15.0.0%2Fble_sdk_app_hids_keyboard.html...
Hi
I used Toolchain Manager v0.10.3 to install nRF SDK v1.8.0 at Mac mini(Monterey - 12.1) two times get same issue.
The issue is Toolchain Manager just download toolchain...
I am using the nrf52840 on the Raytac MDBT50Q-1MV2 module. ( https://www.raytac.com/product/ins.php?index_id=24 )
I am supplying the module with 5v USB power to the VBUS...
Hi,
I'm currently trying to use littlefs as the storage backend for the settings subsys and the internal flash for the actual memory. LittleFS is working in general but...
Hi,
I am using two NRF5340 (one as peripheral and one as central) for our project. Both don't have any display and input capabilities.
For our use-case, I would like to...
Board: nRF52833
SoftDevice: s140
SDK version: 17.0.2
I've added OTA DFU feature to my application. I flashed pca10100_s140_ble bootloader and my application to my board...
We are using a custom nrf52832 HW configuration and the device is entering a state where it's drawing approximately 3mA without any obvious application layer functionality...
