the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Background:
Over the past few weeks, I have been working on enabling TLS1.2 for an nRF9160 with Ethernet (W5500). My primary objective is to have both Ethernet and LTE...
Hello everyone,
Currently we're trying to get the full WiFi stack working on nrf7002dk. We decided to look into the power consumption of the DK board itself as a point of...
The Nordic Thingy:91X board has a Nordic nmp1300 pmic device, but the samples do not support the board (a lot of time would be saved it they did);
https://docs.nordicsemi...
Hi Support Team
Does nRF5340 support UAC(USB Audio Class) protocol? We want to input audio to nRF5340 via I2S and PDM and then output the audio to a PC via USB. Can the...
I would like to save about 100KB of data in the on-board FLASH of the nRF9151 SiP. Can you point me to the memory map and how I can partition the space?
I would like to create either a receiver thread that only monitors incoming/MT data OR setup a callback function to receive all incoming messages. Does such a thing exists...
I am using a custom nRF52832 board with NCS v3.1.0 with the following BT configs:
# Enable Bluetooth CONFIG_BT=y CONFIG_BT_PERIPHERAL=y CONFIG_BT_GATT_CLIENT=y CONFIG_BT_DEVICE_NAME_DYNAMIC...
Hello,
im trying to install the credentials into my nrf9160 , the error i get is this one : Failed to obtain CSR from device.
How can i solve this issue? I have also...
I do step-by-step elements from https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-9-bootloaders-and-dfu-fota/topic/exercise-5-fota-over-bluetooth...
I am trying to implemented a mechanism for authenticated debug on NRF52840 on NCS 2.5.
My understanding from the product specification is that DAP protection is enabled...
HI，
The current SDK version I'm using is 3.0.0 for nrf54L15. I want to control the SPIM30 using DPPI, so I'm using the nrfx library to operate the SPIM30. The specific code...
Hi,
We are experiencing a weird issue on our custom boards which have a nrf9151 chip
We are using emnify sims and have experienced the following:
On some boards, when...
Currently designing around the nrf54h20 and wondering if Nordic has any recommendations for properly routing the USB D+ and D- traces.
D+ and D- are supposed to be routed...
First of all I am very new to all of this and have been reading up a lot on the topic.
I am trying to create a walkie-talkie like setup where 2 development kits will communicate...
