Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
Unable to configure hCI Uart project in Segger Embedded
I need to configure the HCI_UART project to support DTM testing, but I cannot enable the configuration parameters...
Hi
We are a group of students working with the nRF9160dk.
We want to try connecting the nRF9160dk to google cloud and send data through MQTT.
We have tried to follow...
Hi,
We want to build PCB using nRF52840. Previously we were using this package but it is out of stock. I want to ask can we use this instead of the previous package. Are...
HI Team
We are using nrf52832 in our one project. we just want to know the power down state. how we will put the nrf in power down and what actually happens in nrf when...
We have a design where 9160 is always battery powered (, and only the RESET-pin is the way we have to shut it down (keep in reset).
Probably this design might not be the...
i am using SD S140.
i have a 300us period that must take 300us, no more, no less.
for this reason i must call __disable_irq().
when i do it i sometimes get app_error_fault_handler...
I have done a program with keil IDE and am putting into use an ST link v2 for a debugger, and in Keil am getting “internal command error” as the problem.
The screenshot...
Hello,
We are developing hardware with a soldered down eSIM. Our previous LTE module vendor recommended 47pF capacitors on all the signal lines (CLK, RST, I/O) and 47pF...
Hi team,
I understand that it may not be a simple answer, but not sure if we have any clue on the support?
Based on the Devzone ticket: https://devzone.nordicsemi.com...
Hi there,
Recently, we used the nrf52833-DK to develope the direction finding.
We want to add an external antenna array we designed on the nrf52833-DK for AoA receiver...
I have a local carrier SIM card and iBASIS SIM card that came with the nRF9160-DK. LTE-M is activated on the SIM card of the local telecom operator. However, none of these...
Hi, I developed a BLE and Zigbee custom product, starting from nRF5 SDK for Thread and Zigbee v3.2.0. On BLE side, my customer ask me to have the BLE MAC number also inside...
Hello Nordic Support,
I started with a sensor sample project for ADXL362 Three Axis Accelerometer ( https://github.com/zephyrproject-rtos/zephyr/tree/main/samples/sensor...
Hello,
I am using PCA10040 DK for programming my custom board which is having the NRF52832 controller. Until yesterday afternoon, I was able to program my board using NRFgoStudio...
Hello. An LED is connected to the pin of my nRF52832 through a resistor to ground. How can you programmatically determine its presence? I tried to do pullup and read the port...
