Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hello,
We are in pre-production and we need to make 1000 prototypes.
Here is the filter we planned to use : https://www.johansontechnology.com/datasheets/2450FM07A0029...
Hi support team,
Customer needs them for BLE certification though I think those in nRF52840 report are same.
BTW, may I pre-fetch nRF5340's for any future request? ...
Hello,
Have any developers here on the forum had luck with getting the nRF9160 DK working in India?
Our India dev team has looked extensively and has not yet been able...
Hi, dear Nordic.
I tried to build secure_bootloader_ble_S132_pca10040 project in Segger. And it gives me this error message:
cannot find ../../../../../external/micro...
Hi,
I am trying to get my nrf24L01+ to communicate with nrf5340 using the enhanced shock burst sample code. In the sample code there are LOG_INF, LOG_ERR, LOG_DBG commands...
Hello Nordic Team,
We are in production phase, and flashing our modems one by one does not work well. It is too slow process, so we are looking for a solution that can offer...
Hi,
I'm trying to develop a Bluetooth Mesh Network using 3 Thingy52s and one Thingy91 that acts as a gateway to Azure IoT Hub. I saw the sample code LTE BLE Gateway for...
Hi,
I am trying to get the Atmel WINC1500 module to work with the nRF9160DK.
I have read a similar post,
https://devzone.nordicsemi.com/f/nordic-q-a/76640/spi-issue...
Hej!
I am trying to make a circuit / configure my SW for using the nRF5208 to have a small power consumption when not trainsceiving . Basically, I need my setup to have...
Hi! The nPM1100 is advertised specifically as a complementary product to the nRF52 and nRF53 product line. Seeing how the nRF9160 can also operate at 3V, I was wondering why...
Hello, I am working with an nRF52811 and I am trying to get it to send data via UART with a USB connection. I tried using the USB CDC ACM module, but it appears to only work...
Hello,
my application requires a reliable break detection (The serial data input is '0' for longer than the length of a data frame) sent from a peer device on the UART RxD...
I am working on reading and writing data to an external QSPI flash (MX35LF4GE4AD) that has an internal cache mechanism. I have been able to read/write to the flash using standard...
I am currently working on a project developing a USB HID product based on the nRF52840. I have run into an issue regarding USB communication reliability and am seeking the...
