I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
I want to build the sample usb_hci.
After i create a build config there are warning and the process fails
warning: <choice BT_HCI_BUS_TYPE> (defined at boards/arm/ubx_evknorab10_nrf5340...
Do you give us some software workaround to use SPI (P2.08-MISO, P2.09-MOSI )
The Hardware design refers to datasheet v0.9, connecting P2.08 as MISO and P2.09 as MOSI. From...
Hello,
we are testing the openthread CLI example on nRF54L15dk
We have compiled it with the following options:
CONFIG_OPENTHREAD_CHANNEL_MONITOR =y
CONFIG_OPENTHREAD_CHANNEL_MANAGER...
Hi there,
We are using for BLE communication a nRF52832 chip with random static address configuration (shown in the UART). Can we be sure that the address of a chip will...
Hello, I’m working with the Distance Measurement (nrf_dm) module and aiming to implement a centralized topology using Anchor and Tag roles.
The intended behavior is:
...
Hello,
According to my understanding of Bluetooth Core Specification 6.0, Volume 6, Part H, "Channel Sounding", it is not a requirement that the Initiator and Reflector...
Hi NRF support team, We are developing a custom board based on the NRF9151 SIP. I am experiencing some issues in provisioning the device to the NRF cloud. On the 9151-DK i...
Hi,
We develop functionalities on native_sim before moving to embedded, therefore I am trying to have nRF9160 modem connected to Zephyr "cellular_modem" sample on linux...
Currently, as a peripheral, I can discover services like GAP and GATT on the host. However, I'm encountering issues when trying to discover the ANCS service. When calling...
Hey All,
Last month a network provider had some internal issues which rapidly started rejecting our devices with several EMM registration issues, however due to not seeing...
Hello All,
We have developed a Zigbee End Node device for which we would like to make a radio test.
we are using nRF connect SDK 2.0.0, please note the reason we use the...
Hello Nordic Team,
I’m currently working with the nRF5340-DK and nRF Connect SDK (v2.6) using VS Code . I’ve been testing OTA firmware update processes using MCUboot and...
Hello
I need help, I have a problem implementing ppi gpiote and spim. The ADC I use is mcp3562 which sends via the irq pin when the data is ready. I need to work in continuous...
I used Nordic52480 DK(bulb) as DUT to run Matter Certification case TC-DGGEN-2.1 .
Steps:
1. setup OTBR on Pi4：./certification-tool/backend/test_collections/matter/scripts...
Hello I have an nRF52840 board with a 2 MB external flash I'm using SDK 2.6.2 I'd like to configure the mcuboot_secondary partition to be on the external flash
Here is my...
