Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hello!
I am sending MQTT commands over UART from an NRF52840 DK to the NRF9160 DK which has the ibasis sim card inside. I noticed 3 times so far that after 24 hours , 1...
Hi
I could test Bluetooth Mesh Chat sample on nRF52833-DK nodes. I would like to know whether there is any way to send chat message from nRF Mesh app (non-mesh BLE device...
Hello,
I need to send and receive UDP packets using nRF9160DK via NB-IoT network. I'm able to achieve this using Serial LTE modem . However I need to write my own application...
Hello,
In a design we plan to have 2 x SPI, 1 x QSPI and 1 x I2C interface. For the SPI we plan to use one @32MHz and the other @8MHz.
Please confirm there no "instance...
Hi everybody,
we are trying to bring our beacon's consumption as down as possible. We have nRF52832 mounted on our custom PCB with external 32 kHz crystal and DCDC is enabled...
Hi, I am using the Nordic nRF53DK, with the Segger IDE, in the NCS 1.5.0 release.
I'm playing around the Data Length Extension with the Sample of the Central UART...
Hello, My environment is nrf SDK v1.5.1. The board im developing for is the nRF52840DK. I'm trying to do some ECP-Calculations and therefore Ii want to use some function located...
Hello, All
I want to implement OTA using Thread with nRF Connect SDK.
Is there any sample code or reference this can be done with Thread?
Even if there is any experimental...
Hello,
I have a: nRF5340DK connected to Windows10 PC via USB.
I also have these that are working fine in terms of being able to communicate with the nRF5340DK over Bluetooth...
nRF SDK version is 1.5.1
upgrade modem fw to 1.3.0
Is there any way to do software reset on GPS modem? I have ran the gps example and I notice that "printk" sends everything...
I'm using the nRF5340 DK with the HRM example. My phone is HUAWEI mate 10 (Android 10).
I could scan the Zephyr Heartrate Sensor in nRF Connect App and nRF Toolbox App ...
Hi Team,
In continuation with Case ID: 269054, 269278
I am using NCS (as suggested) to avoid high current consumption happening during softdevice initialization.
I set...
Hi, I'm enthusiast of nrf5340 DK. BUT: in the samples I'm not able to find some viable openamp (other ipc seems to have the same problem) example. I am looking for a way to...
To the kind Nordic support team,
I have got a nRF52833 based Raytac module I'm using to develop before using a custom board.
I'm using Microsoft Bluetooth Virtual Sniffer...
