I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
We are using this BLE chip (nRF52840) in our hardware, and we have written its corresponding code in Android too but Android app needs Location permissions and GPS...
Hello, I just started using a Decawave module running a nRF52 chip. As a starting point, I closely followed the guide provided on the official website, but after doing everything...
Hi,
I need to connect nrf52833 (BM833 module) with host controller. what are all the interfaces needed to communicate with host controller? help me out in this.
Kindly...
I used 2 channel saadc, channel 1 and channel 3.
Maybe in the first few minutes, it's done ok,
p_event->data.done.p_buffer[0] is belong channel1 adc value
p_event->data...
Hello,
We have integrated the FATFS example as shown in the usbd_msc example project into our own firmware application. It works perfectly on the nRF52840dk and when we...
Hi,
I want to check time line of my project using segger SystemView.
- SDK 16.0.0v
- ESB example
- nRF52832
When Start recording, "Could not find RTT Control Block...
Hello Team,
I want know how to use RESET pin [pin. no. 21] as a GPIO.
I followed below thread but it not work for me!
devzone.nordicsemi.com/.../disabling-pin-21-of...
Hi:
What's the marking on the nRF24-LU1+?
Marking exactly "nRF24-LU1+" or any chance marked as "nRF24-LU1" instead? Your big assistance & prompt feedback is much appreciated...
I am using NRF52810 in : In advertising mode not able to erase or write to flash sd_flash_page_erase. hungs up via processing commands from nrfx_twis_state_machine
Hi,
I'm developing a custom application starting from ble_hrm_freertos application. When NRF_LOG is enabled there is no way let the chip in low power consumption. I found...
Dear Technical Support,
I have faced a problem debugging firmware on our custom board based on Nrf52811. We use j-link EDU and Segger Embedded Studio as development tools...
Hello Nordicsemi community,
1) manual build of mcuboot - When trying to build the mcuboot for nrf5340 via the mcuboot/samples/zephyr via the west build command, the build...
HI , nrf52832 with SDK v16 on that using this nus example location below mentioned
examples\ble_peripheral\ble_app_uart\pca10040\s132
in this example, didn't change...
Hello,
I have recently received the nrf5340 development kit as part of the Hackster contest.
I followed the webinar and to get started
1. Connected board via micro USB...
