According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi everyone,
I work on an custom board with the nrf52840, the SDK 15.2.0, the SoftDevice 140 6.1.0 and FreeRTOS.
My problem is that during a BLE transfert of a lot of...
Can I develop a software with MESH network support (1MBPS) and 16 Central links (CODED_PHY)?
All my tries is unfortunaly. But I dont give up.
Just guide me please and...
Hi, I have 2 nRF52840 D K but suddenly both are not showing on my PC. I have checked my data cable which is working fine on mobile and transferring data. I have also checked...
Hello,
I am evaluating the possibility to use ESB protocol on nRF52840 development kit. As far as I understood, for HW limitations, the maximum number of pipes in a star...
Hi all.
I want to increase number of sending packets in TI. I searched for the answer and I found answer wasn't for v7.2.0.
please give me a solution for v7.2.0 sdk ....
Hi
I want to receive data through UART RX interrupt.
--> A n interruption occurs to notify me w hen one character(byte) is received, and i store it to my memory buffer...
Hi everyone!
We're working with the processor nRF51422 with S210 softdevice and we've found an issue about the QDEC sample frequency. In fact, the minimum sample period by...
i have nRF52840 Dongle (PCA10059) and when i connected the dongle and opened nrf connect SDK application and tried to run BLE, then i am getting the following error. Kindly...
I am following the step to install my nRF52DK, but when I check it with "python3 nrf_sniffer_ble.py --extcap-interfaces", it has some error:
Could anyone help?
Hey!
I will post the whole code if necessary but for instance as I thought it would be a little glitch in my code, I tried to explain the basics of my problem for now: ...
ASSET TRACKER V2 Modem problems:
I have set up asset tracker V2 for nRF9160 and it sends the messages (GPS, Temp, Hum, etc) and the corresponding timestamps, which I can...
Dear friends,
I followed the tutorial( Using serial interface for provisioning and configuration ) control a mesh node.
a) The PyACI as a host via uart connet to 52840...
I'm running NRF Mesh3.1.5 in Android on my Galaxy S10. I'm following the steps in the Bluetooth Mesh Developer Study Guide and can connect to the Switch an Light nodes as...
Hi,
I wanna my appication run first instead of bootloader. Here is my steps:
Create bootloader_setting: nrfutil settings generate --family NRF51 --application application...
