the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
SDK 14.2, NRF52840, S140
Hi,
Thank you so much in advance for answering my very long question. I am a little confused by the low power pwm example and app_PWM documentation...
Dear Nordic Technical Support Team,
I am developing a Mesh consisting of a client requesting to a net (group) of server nodes some motion data (which triggers automatically...
hello all,
nRF Connect SDK: 1.5.0
nRF Connect Toolchain: 1.5.0
Desktop OS: Windows 10
I'm currently using nrf9160dk to explore the GNSS features. I take a look at...
Hi, I'm using the SLM application and I would like to test the PSM on the nRF9160-DK but its timers seems to be aperiodic (instead of periodic). I set it using the at command...
I want to use a UART line to send and receive data to a nrf52840 DK and then have the data sent wirelessly to a separate DK and then print it to a terminal like in the multi_sensor...
Hello,
currently am working on connecting two different modules of BLE, nrf51822 and Rn4871.
The problem am facing is that i am not able to send and receive data between...
Hi,
We are using mesh SDK 5.0 on NRF52840 integrated with PIR and light level sensors for office lighting, it works well.
Now we'd like to check if we can expand the system...
Hi while implementing/testing MTP on Linux Wireshark captured setup requests asking for "Device Qualifier Descriptor" according to section "9.6.2 Device_Qualifier" in the...
Hello,
Can you please provide information for current consumption of the GPS in these modes?
VDD=3.8V
Acquisition time = ? seconds
Acquisition current = ?mA
Tracking...
Dear all,
For our project we want to store information on the device in an additional flash partition. We have created a new flash partition, called factory_settings_partition...
Helo Nordic support team,
I am supporting a client that has designed a product using the NRF9160 with GPS. The product has a small patch antenna mounted on the pcb board...
Hello. I am trying to build an project and I need to use RF module. And I have to Use pic18f45k22 with MikroC. But I couldnot. I have some 18f45k22 codes but dont work I dont...
Hello,
I need to retrieve the IP-Address of the modem, are there any convenient way I can do this?
AT commands maybe?
Appreciate any info on this.
With regards...
Hello
I am having rather odd problem with SWDIO pin shorted to ground. I am using Fanstel BT840x BLE module and I have never seen this issue on my custom board until last...
