Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi, I'm using nRF52832 Software Development Kit, PCA10040, S132.
I'm trying to follow this example.
I connected successfully, but I have problem in 'Advertising' part...
Hello, Support team:)
I wish to use NRF_LOG_DEBUG function in segger embedded studio.
But there is no message in "Debug Terminal".
- nRF SDK 16, "/examples/proprietary_rf...
Hi
I am now working on a project which I use ble_app_uart_c as a reference.
SDK 16 and used softdevice s140.
UART works normally at 3.3V.
But if I lower the power...
Greetings. I am on a mission to upgrade the BLE Firmware of nRF52840 via UART and ultimately via the UART communication between our main Micro (Microchip PIC) and nrf52840...
Hi,
I am developing a product using nRF52832 . (S132, SDK 17, IAR8)
I am developing based on the ble_app_uart example.
I would like to add a basic PWM code to...
I had some issues with Errata so I tried to build a simple BLE app like Blinky.
The errata functions all compile as return false. For example, nrf52_errata_108
What...
I would like help in understanding the limitations of the NVRAM. The documentation for the nRF52840 and the nRF52832 are different. This is what the nRF52840 reads:
Do...
Hello all,
I am new to BLE mesh programming. I want to develop a multiple sensor client-server model where sensor data (eg. temperature values) from multiples nodes in a...
Setup:
- MESH SDK 4.1.0
- nrf52832.
Consider the following scenario:
- 3 nodes (A/B/C) are provisioned on the same network.
- I'm using a custom model with reliable...
Hi Team,
nRF52840 boards are getting fail continuously not able detect by Host computer.And the boards are no more useful and all boards are brand new only One day we have...
Hi,
I am trying to enable Bootstrap support.
Therefore I set "CONFIG_LWM2M_RD_CLIENT_SUPPORT_BOOTSTRAP=y" in prj.conf.
I also set "CONFIG_APP_LWM2M_SERVER" and the port...
I have built boot-loader hex file from SDK 12.1.0 secure DFU project, without any changes except for public_key.c file.
I am referring to steps mentioned under
Combine...
Dear all,
Hi, I'm Eric.
I m studying spi communication used nRF52832 base on SDK 14.2/example/spi.
That examsignal is below picture 1.
But I want to delay between...
Hi--
I noticed something rather peculiar on the built hex from segger that is programmed onto my nrf52832 chip (firmware image).
The hex looked as expected, until i got...
My ble_peripheral is bonded to ble_central, How do I upgrade at this time ? If you still use the mobile phone APP to upgrade, you need to erase the binding information, and...
