Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
Dear Nordic Support Team,
I'm working on a BT Mesh implementation and came across a problem with the proxy enable / disable feature.
Disabling the proxy function doesn...
Hi all, I'm working on making mesh sdk work with peripheral uart example. I tried to merge peripheral uart example (nRF5_SDK_15.0.0_a53641a) into proxy_server example (Mesh...
Hi,
I was into the working of bluetooth mesh. I was wondering if it is possible to configure a bluetooth mesh network with a smart phone acting as a provisioner and by any...
My aim is to establish communication via nRF52840 dongles. This means if I connect mobile phones to the dongle and the data sent by one mobile phone should be received by...
Hi
Does the nRF52840 and 52832 support automatic gain control (AGC) for for BLE?
See this Ti post which suggests AGC is not used for BLE
http://e2e.ti.com/support...
I have recently migrated from SDK 15.0 to 15.2 and are experiencing problems with my code.
I have a nRF52840DK and have attached two accelerometers to this board. I am able...
Hi,
I'm currently working on achieving BLE NUS + ESB UART concurrent implementation via timeslot API, by referring to the example here . I have ported it to utilize SDK15...
Hello,
I'm using nRF5 SDK with version 15, nRF52832 IC and softdevice s132. I need to save hold the data in the ram even in sleep mode. I'm using the below code. However...
How can I return my nRF52840 DK to its out of box condition (firmware, demo) so that I can turn the device over to a colleague and let them run through the getting started...
1. SDK version : nRF5_SDK_15.0.0
2. Platform : nRF52832
3. Purpose: NUS service with example ble_app_hrs_rscs_relay.
4. Problem : NUS device connection only success...
Using a Peripheral set in Central mode and write then read data back in the Dongle nRF5240 set in Server Mode.
Once connected and exchange MTU (extended) I write and then...
Hi Developers,
I am exploring the light switch examples, client, server and provisioner, every time a node is provisioned it uses a unicast address, what if I want to use...
Hi all,
In our project we are using nrf52810, SDK 15.0.0 and ble_app_uart.c example.
We are using our custom board in which MCU is communicating with BLE through wired...
Hello,
So i found this code from one of the earlier post which combines the saadc example with ble_app_uart example to make analog values from the analog pins to be sent...