Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am testing nrf5 IoT tcp client example. (in \nrf5_iot\examples\iot\tcp\client)
DK side:
IP:2004::213:ddff:fe4c:6032
run as client.
2.6lowpan border router...
I'm using the ble_app_template of SDK11. but I dont have an external oscillator, so the run time freeze at ble_stack_init
in this answer , the solution is to relace NRF_CLOCK_LFCLKSRC_XTAL_20_PPM...
Hi,
I have a NRF52DK (Chip Label: PCA10040; V0.9.0; 2015.44; 682646724) and when i try to start the DK as described in the getting startet page, Step 5 failed as LED1 is...
Hi,
I am planning to make a program so that when a beacon goes far away a specific distance (around 5m) then the led should light up.
I have taken some measurements...
Hi,
I have a couple of eval boards that were created for software and hardware development. We have two versions of the nRF52832 on these development boards. I know that...
I am using nrf51822 powered by a 3.3V regulator in a li-ion powered application. We have a high current load that we're controlling with PWM at 20kHz. Radio performance is...
I want to bond with an peripheral, which has static passkey hardcoded in it. If I want to bond with it with MCP, I get an request for passkey, I can then bond and encrypt...
My environment for this is
Ubuntu 14.04
ecipse Mars2
ble_app_uart project of Nordic SDK11(makefile project)
armgcc
nRF52 PCA10040 Nordic board
ERROR...
I am trying to figure out how to exit a loop of my program using a button press on the nRF Toolbox UART app. Say it's button 4 for sake of giving it a value. I am using an...
Hello,
I've been trying to use nRF Connect 1.0.0 on OSX 10.11.6 with a nRF51822-powered board ( this one, to be precise ). Whilst nRF Connect finds the serial port and...
Hi,
I'm complete nordic newbie and asking you for some help.
I have 2x 81522 ICs, one is QFAAC0 and the other one is QFAAH1, both QFN48 packaged.
(1) looking at infocenter...
Hello I'm trying to learn your API using nrf5-ble-tutorial-advertising example. Over all the example is much help and API documentation is quite good. But part of API code...
Hi,
I am trying to do a GPIO operation every one second repeated in 51822. I am using app timer to get this work done. The current average consumption is 45uA/H. The handler...
The blinky_freertos example in the nRF5 SDK 11.0.0, built for the nRF52 (PCA10040) with GCC, appears to work fine right out of the box. However, when I added -DDEBUG_NRF to...
Hi,
Is it possible to communicate directly between nrf51dk(peripheral) and PC(master)?
With UART communication, I need to connect a board to the PC via USB. But I want...
