Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
I have a custom board with an I2C connected sensor ADXL345. I have to do GPI/O initialization to select the I2C. This works because I can read the ADXL with custom I2C commands...
Hi
I am using nrf52840 in my custom board. I have a gpio button which is assigned for as a factory reset button. So when i press the button the whole board needs toi be...
Hello,
we are looking to develop multiple BLE audio source which sends the mic data to the receiver and the receiver receive the audio data from multiple transmitters...
In my design, I aimed to isolate the USB interface. To achieve this, I used the Analog Devices USB isolation chip, ADUM3160BRWZ, to isolate the connection between the PC and...
When I need to switch between 1M and 2M
I create an object of the type bt_conn_le_phy_param and fill in the parameters appropriate to the radio mode I want, and then I call...
Hello,
I would like to know if the nRF9151 is suitable for building a product that will be able to monitor (read) multiple pulse signals originating in utility meters (electric...
We are using nRf5340 and nRf7002. In our application , we are connecting wifi and goes to ksleep for few minutes.
After wake up from the sleep. wifi is not reconnecting...
Hello all,
I ported an old nrf5 application from SDK 12.3 to SDK 17.1. It uses S112 7.3.0 and FreeRTOS. Unfortunately I am getting time variant softdevice hard faults at...
While testing nRF FOTA download library we noticed that it supports only one image update at a time (download image, then reboot).
Irrespective of the image (either application...
Hello, I just upgraded from SDK v2.5.0 to v2.7.0 and now I have a problem updating the bootloader.
In my project I have b0, the mcuboot (in s0 and s1) and the application...
Hello, I followed Getting started guide for the nRF54L15 PDK ( Getting started with the nRF54L15 PDK (nordicsemi.com) ) and bumped into a problem when i try to build "hello...
I am using the following example as a reference for setting the TX power in a peripheral Bluetooth connection: https://github.com/nrfconnect/sdk-zephyr/tree/v3.6.99-ncs2/samples...
Hi, we are doing testing with a Nordic dev kit and looking for ways to check the status of GNSS.
We are becoming familiar with the XGPS command and notifications: docs.nordicsemi...
How can I return from k_sleep (or any other "sleep" method) when an interrupt occurs?
I would like my device to sleep (low power) until a GPIO pin toggles, then wakeup to...
