I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
I use nRF52840DK and nRF21540EK to develop BLE programs, and the program uses FLASH for BLE image storage, the program works well on the DK. However, when I burned it into...
Hello,
I try to flash my bmd-345-eval board with nrf connect visual in VS code.
But the connected devices don't show mcu but show VCOM0 and RTT on nRF connect in VS code...
Hi
I have a issue, I have 4 samples nrf9160 module, all run in same firmware with FOTA feature
I found that only one module cannot start FOTA, then I try to read message...
I am getting the following build error for a Nordic nRF5340dk
c:/ncs/toolchains/ce3b5ff664/opt/zephyr-sdk/arm-zephyr-eabi/bin/../lib/gcc/arm-zephyr-eabi/12.2.0/../../.....
Hello,
We have an issue regarding PSM availability when roaming. Some operators do not grant PSM and once a device connects to such a network, it would drain the battery...
Hi, When performing GATT discovery on the peer device I observe that the procedure takes too long about 5-6 seconds even at the lowest connection interval. The same process...
I was trying to add the nrf91-modem-trace-uart snippet to my build configuration. I've found that it does not take effect when using the "Add Build Configuration" UI in the...
Hi support team
If I want to implement update advertising data dynamically function, which method is recommended?
1. bt_le_adv_stop (); and bt_le_adv_start (adv, ad, ad_len...
Hello,
I am primarily an STM32 user, delving into Nordic. I will be creating a product using the nRF52832. I would like to measure the 32MHz & 32KHz clock inputs to the...
This is a request regarding modules that can be used in Pakistan. We think that nRF9160 is matched for this requirement. Could you please tell us whether nRF9160 is okay or...
Hi, We are using nrf9160 and building the application with CMSE. When my program accesses dynamically requested memory (address 0x200128b0), the program automatically jumps...
We plan to use the Nordic Semi Thingy will be used with Quectel YB0014AA antenna for the demo sites, all located in North America. The Nordic Thingy is fully FCC/ISED compliant...
Hi,
I am evaluating using NRF9161-LACA in a design. Is it possible to activate this chip with esim? Or we have to use a physical sim card for it?
Please let me know, ...
Hello,
We are evaluating a solution for our product where we would like to use
Zephyr RTOS with NCS
nRF52840/nRF5340 + nRF7002 for a combined WiFi/BLE solution. nRF52...
I have been trying the aws_iot sample in nRF Connect SDK v2.7.0 for build target nrf7002dk/nrf5340/cpuapp, in which connect_work is scheduled with a 5 second delay in the...
