Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
I have tried to follow the Zephyr CLion instructions and got it to build. However I could never get to the point where I could run or debug the project on the device. Various...
Hi,
I am writing to seek assistance with an issue I've encountered while attempting to create a modem trace on my nRF9160DK board.
When flashing my asset tracking code...
i have to use mqtt for my project. Now am using nrf 52840 for transfer data to from my device bt840 if i want to go with MQTT have to connect wifi module with ble.
esp32...
Hello!
I am programming BLE with the nRF52840-DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0, window11 pro]
I am integrating NUS Central...
Hello!
I am programming BLE with the nRF52840-DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0, window11 pro]
I am integrating CDC ACM...
I'm using version 2.0.0 of the Android version of the device manager app. When I select my device from the list to do a DFU it immediately closes the app. Normally it would...
sometimes the param update will fail and sometimes will not. May I know what the reason is and how to solve this issue?
error case;
normal case:
my prj.conf...
Below are power consumption measurements of a DUT being booted with the same PPK2 in SMU mode with various software versions. The only variable being changed is the PPK2 software...
Hello all,
I want to use nrf52840dongle to receive notifications from other BLE board.
I have tested with nRF Connect for Desktop Bluetooth Low Energy successfully.
...
Hello,
I'm using nRF5340 audio application with nRF Connect SDK v2.7.0 on nrf5340 Audio DK.
I didn't change anything in the sample code but only modifying the NRF5340_AUDIO_TRANSPORT_MODE...
Hi there,
I generated the DAC, PAI, and PAA certificates using the chip-tool and merged them into my firmware as factory data. Additionally, I generated the Certificate...
conducted an ADC experiment using the nRF5 DK (PCA10056).
The power supply for the nRF5 was provided via USB.
Based on the SAADC sample, I coded the following:
...
I am using an NRF52840DK.
1. I erase the chip to start clean:
nrfjprog --eraseall
2. I flash the MCUboot bootloader:
~/mcuboot/boot/zephyr$ west flash
The output...
