Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
I would like to test event related functions on nRF5340 DK. But west build failed with undefined reference to `z_impl_k_event_init'. The following are log messages of west...
Hi,
I am trying to connect 4 devices (2 nrf devices + 2 B24 custom modules). Each of them can get connected independently as single device, but as soon as I start connecting...
I'm reading the code of peripheral_hids_mouse project and I want to select some functions to fill my own code.
prj.conf has these two config:
CONFIG_BT_GATT_UUID16_POOL_SIZE...
Hi,
I followed SDK 2.7.0 Fast Pairing example and successfully downlowd to nRF52840 PCA10056 EV board, using VS Code nRF Connect Extension.
Fast Pairing Input Device example...
Hi,
I am hoping to send/receive binary data (a protocol) on the same UART that has logging/shell enabled. Is there a way to access the UART RX traffic that the shell gets...
Hi all!
I've been working on a project using the nRF Connect extension for VS Code and I've been trying to figure out which HEX file in my build/zephyr folder for my application...
Hi,
I am sending a SCAN_REQ packet from my code after receiving an Advertising packet from the NRF5340 DUT. Sometimes I receive the SCAN_RSP packet, but other times I encounter...
I am working on a project where my hardware includes an array of LEDs. I want to run an LED pattern on the array during the DFU process. I have tried to find a solution for...
Hi, I have been working with I2S Mic sph0645lm4h-b and nRF5340 audio DK. I configured mic and while I'm reading the data it throughs an error code of -5. I'm Sharing the code...
I am a beginner and I want to switch from SDK 17 to nRF connect SDK v2.6.0, but I found that many configurations are different, such as gap initialization, gatt initialization...
Hi,
In my wearable application, I would like to have reset functionality by pressing two buttons, which I also would like to use as application interrupts. I read that the...
I'm working on implementing asynchronous UART on a nRF52840dk but uart_callback_set() is returning -88 (ENOSYS), which according to the tutorial here means it's not supported...
Hello!
I am using a nRF52840 board for some really simple development. First I just tried to run the blinky example and connected with another BT device. It worked well...
I attempted to use https://github.com/Protocentral/protocentral_max30001_zephyr_driver to build my project. However, I am still encountering some issues.
1.In the overlay...
Was following steps here to set up the sidewalk sdk from a blank nRF Connect SDK for VS Code application template using sdk v2.7.0. I noticed immediately that the directory...
