I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello NRF team,
We have been using NRF52832-QFAA based dev kit from Sparkfun, which has 512KB Flash / 64KB SRAM. I developed the app on Arduino whereas I flashed the bootloader...
Hello!
Here is a story I am sure you have heard before. I am evaluating the NRF9160DK and seeing what is the lowest power consumtpion we can get when sending data to a server...
I have an existing product using the nRF52832 SoC rev 1. We must transition to rev2 since rev1 is no longer sold. We use SDK12.0.0, with S132 V3.0.0. Have these software components...
Hello Team,
I have downloaded the Zephyr project and working on the LwM2M sample client application to make nRF52840 DK as an LwM2M client. I have followed the below link...
Hi,
Referring to White Paper nRF9160 Hardware Design Guidelines v1.0, what is the scenario (supply voltage, band, antenna VSWR, TX duty cycle...) behind maximum heat power...
Dear Sir,
I'm using nordic's example codes above to tx and rx, but i can not get them working properly. the LEDs should light on the receiver side according to the example...
I have a strange issue on the nRF9160-DK board using the nRF Connect SDK, GNU ARM for GCC v10.2.1, built using makefiles.
I have two threads that both wait on a semaphore...
Hi,
I am trying to change the tx power of Zigbee using the following APIs :
1) zb_set_tx_power(0x32); 2) nrf_radio_txpower_set(NRF_RADIO_TXPOWER_NEG12DBM); 3) nrf_802154_tx_power_set...
I am currently using a nRF52-DK to follow the connection between two external devices. I run the sniffer and start/stop the sniffing via Wireshark. When I start sniffing,...
Dear Team, I face Following error with example downloaded from Github,
error 1) Output/Release/Obj/saadc_pca10040/ses_startup_nrf_common.o: in function `InitializeUserMemorySections...
Chip: NRF52840
Firmware platform: Wirepas V5
Hello!
I am now writing firmware for a product based on HW&SW mentioned above.
It is powered by battery and sends data...
Dear Sir,
please do me a favor to reply on my following question.
our project is a keyboard which we expect can work on both ble and 2.4G. we will use other brand of of...
Hello
I am using nrf52832 and sdk v17.0 I recently succeeded in controlling several ws2812 LEDs through I2S. And now I'm going to combine these codes with the others.
...
