the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
I have modified the ble_app_hids_keyboard_pca10040_s132 example to enumerate as a Gamepad and Modified the GPIO so the buttons send a USB report.
I am now trying to integrate...
Hi,
I am doing some customization for the secure DFU example (SDK15) and i want to add conditions for the update process (battery level for example).
I wonder if there...
Hi all. I would like to get the current RTC tick when there is an advertisement RX event on multi-link central. I am going to store the advertisements along with a time i...
Hello, In one of my codes, I use the printf function. It works properly when implemented in the int main(void), but when I try to use it in a static void NAME (void){} function...
Hello,
I'm checking the DTM code from nRF5 SDK15.2.0.
In the ble_dtm.c file, line 763:
And in the ble_dtm.h file lines 104-110:
DTM_PKT_0XFF and DTM_PKT_VENDORSPECIFIC...
Hi.
We got Thingy for power measurement purposes. I tried first the it out of box and it works fine. Same with pre-built image.
However if I build the SDK example and...
non connectable advertise success when in SDK 8.0.0, however I got error code 0x00000007 when upgrade to SDK 9.0.0.
I find out error code 7 is NRF_ERROR_INVALID_PARAM,...
hi,
my development kit nrf52832 is not detecting via phone nrf connect app . it appears like no device found .i flashed the ble blinky example program (sdk 15.2version)...
Hi to everyone!
I recently bought the nRF52 SDK to use it in a project, but the kit contains a NFC antenna and I don´t know its use.
My project its about Bluetooth Mesh...
i use the sdk15.2.0, the chip is nrf52832,my device have both BLE peripheral,and BLE center in my application, I use center to connect with peripheral, i directly use the...
HelloI am trying to program nRF52832 QFAA and am succeeding only partially: the debugger is connecting to the chip, and I can RUN step by step, however, I'm seeing only the...
Hello, I have adjusted the Uart Central Example from the SDK 15.1.0 with the stack s140 v6.1.0 so that the device can connect to two peripherals. The name of the device is...
Hi All,
I use SDK 15.2 to periodically trigger ADC acquisition tasks via PPI. But SOFTDEVICE: INVALID MEMORY ACCESS error occurred while the system is running.
I found...
I am using nrf52832, SDK v14.2, Softdevice s132_nrf52_5.0.0.
I had program the softdeive in flash, and I program the DTM firmware as application(start address set as 0x23000...
