nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
Hi,
We are currently planning to start a project using the nRF52832 as our controller, SEGGER Embedded Studio version 5.42a as the IDE, and nRF5 SDK version 17.0.2 as our...
The scan window does not alternate properly with the BT_LE_SCAN_OPT_CODED option in the scan parameters. Specifically, the scan window does not toggle on and off every 30...
Hi. I want to report 2 observed bugs about board creator wizard of NCS 2.8.0.
1. When you click on "Create a new board", the first thing that you must enter is human-readable...
I'm trying to activate low power mode without success. I found samples but it appears not to work with the last NCS version. I want to get basic GPIO INPUT values at 32khz...
Hi,
1. I am testing nRF54L15 PDK PCA10156 0.8.1 Example is: ncs\v2.8.0\nrf\samples\bluetooth\direct_test_mode 2. Which pins can be used as UART TX and which pins can be...
Hi,
We are currently planning to start a project using the nRF52832 as our controller, SEGGER Embedded Studio version 5.42a as the IDE, and nRF5 SDK version 17.0.2 as our...
Trying to set up UART/UART0 for async. I cannot get the uart interrupt config to shut off.
CONFIG_UART_INTERRUPT_DRIVEN =n is set in the prj.conf
In config output...
Maybe the title doesn't make that clear.
First of all, I have customed my own nrf54l15 board, and I successfully built and run some ncs demos.
Now, I want to do something...
Hello Nordic team,
just received my first hardware and try to port my code which I developed by using the 54L15PDK board with SDK 2.7.0. At the PDK everything did run fine...
Hello,
What is the max data size for NUS?
According to BLE data throughput in the S140 document, it looks like 247 but the data was sent successfully with NRF_SDH_BLE_GATT_MAX_MTU_SIZE...
Hello, I want to configure the radio between two nRF52810 devices. I have an external 32.768 kHz clock and the NN02-101 antenna. My question is: how can I configure the radio...
Hi all,
Ive been able to develop for a few weeks with our nrf52840 device and were able to run our code and do some basic Bluetooth stuff. Suddenly I can no longer flash...
Hi，
How to resolve the following burning errors: PDK:PCA10156 0.8.1
SDK ncs v0.8.0
example :peripheral_uart
Thank you for all your assistance. Kind regards, Peter...
Dear devzone, I used two nRF52840-DKs to download v2.8.0\nrf\samples\bluetooth\mesh\dfu\distributor and v2.8.0\nrf\samples\bluetooth\mesh\dfu\target programs, and configured...
I have gone through the training on debugging because I am getting a stack overflow error, however the debugging screen does not have RAM on it, like it shows in the Dev Academy...
